background image

EN

5

radiant heater IR 2010 / IR 3010

Device depiction

IR 2010

1

2

3

4

IR 3010

1

2

3

4

No.

Designation

1

On/off switch

2

Wall holder with adjustable inclination angle

3

Heating rod

4

Grille

Transport and storage

Note

If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.

Transport

Before

 transporting the device, observe the following:

Switch the device off.

Hold onto the mains plug while pulling the power cable out
of the mains socket.

Do not use the power cable to drag the device.

Allow the device to cool down sufficiently.

Storage

Before

 storing the device, proceed as follows:

Hold onto the mains plug while pulling the power cable out
of the mains socket.

Allow the device to cool down sufficiently.

When the device is not being used, observe the following
storage conditions:

dry and protected from frost and heat

in an upright position where it is protected from dust and
direct sunlight

with a cover to protect it from invasive dust, if necessary

Place no further devices or objects on top of the device to
prevent it from being damaged.

Summary of Contents for IR 2010













Reviews: