background image

EN

11

laser distance measuring device BD8M

Maintenance and repair

Battery change

Note

Make sure that the surface of the device is dry and the
device is switched off.

A battery change is required when the battery indication flashes
in the display or the device can no longer be switched on.

Cleaning

Clean the device with a soft, damp and lint-free cloth. Make
sure that no moisture enters the housing. Do not use any
sprays, solvents, alcohol-based cleaning agents or abrasive
cleaners, but only clean water to moisten the cloth.

Repair

Do not modify the device or install any spare parts. For repairs
or device testing, contact the manufacturer.

Errors and faults

The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.

Fault

Cause

Remedy

The device can no
longer be switched on.

The batteries are
empty.

Insert new
batteries (see
chapter
Maintenance).

Display segments are
only faintly visible or
flicker.

The battery voltage
is too low.

Disposal

The icon with the crossed-out waste bin on waste

electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. You can also find out about other return options
that apply for many EU countries on the website 
https://hub.trotec.com/?id=45090. Otherwise, please contact an
official recycling centre for electronic and electrical equipment
authorised for your country.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.

 In the European Union, batteries and accumulators must

not be treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6 September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.

Summary of Contents for 3510205157













Reviews: