background image

- 4 -

Operating Elements

q

Fan (on the rear panel)

w

12 V vehicle plug

e

On/Off switch

r

AC socket

t

Operation LED/Overload indicator

Initial operation

Unpacking

1. Remove the device from the packaging.
2. Remove all foils.

Warning:

Do not permit small children to play with pla-
stic 
packaging.
There is a risk of suffocation!

Check the items supplied

Before putting the device into use check to ensure
that all of the items listed are present and that there
are no visible signs of damage.
-

Power inverter with 12 V vehicle plug

-

This operating manual

Operational information

For continuous operation of devices via the power
inverter the 12 V vehicle socket must supply a voltage
between 11 - 15,5 V 

.

The voltage source of the 12 V vehicle socket can
be perhaps an automotive battery or a regulated
DC voltage like a transformer-accumulator station.
Before connecting the power inverter check to see
that the voltage source is supplying sufficient power
for operation. 

The required power needed for operation can be
calculated as follows:

Example

The power source should also supply at least 14,7 A.

Attention!

Never connect the power inverter to a 24 V
supply system. Otherwise the device will be da-
maged. The device can only be connected to a
voltage source with a nominal voltage of 12 V.

Setup

• The power inverter should be positioned on an

even, flat surface. Make sure that there is 1 cm
free space remaining all around the power inverter
for air circulation.

• A distance of 50 cm must be maintained behind

the fan's 

q

ventilation slots.

In vehicle operation

If you are operating the power inverter in a vehicle
make sure that the installation is not a hindrance
when driving the vehicle. For this, install cables so
that they do not come into contact with moveable
parts in the vehicles interior and they do not obstruct
the view.

Note:

The power inverter can also be operated when
the engine is switched off. However be aware
that the power inverter possibly may not func-
tion during an engine startup.

IB_KH3906_BK45891_EN_LB6.qxd  10.12.2009  10:39 Uhr  Seite 4

Summary of Contents for KH 3906











Reviews: