3
Installation & Telephone Set-Up
Telephone Set-Up
•
Set Time
Scroll to 'SET TIME' on the System Menu and then
press the Jog Wheel. Turn the Jog Wheel to the desired
time and date pressing the wheel for confirmation after
setting HOUR, MINUTE, DATE & MONTH.
•
Set Recall
Scroll to 'SET RECALL' on the System Menu and then
press the Jog Wheel. Scroll to TBR (Timed Break
Recall) or EARTH (Earth Recall) then press the Jog
Wheel to confirm.
If TBR is selected, after pressing the Jog Wheel you will
need to select the TBR timing (100ms to 1200ms).
Once again press the Jog Wheel to confirm your
selection. The standard setting for the UK is normally
100ms.
NOTE:
By default your NRX EVO 450 is factory set at
TBR 100ms.
•
LCD Contrast
Scroll to 'LCD CONTRAST' on the System Menu and
then press the Jog Wheel. Select the desired LCD
contrast then press the Jog Wheel again. The default
setting is 3.
•
Message Waiting Type
Scroll to 'MESSAGE WAITING' on the System Menu
options and then press the Jog Wheel. Scroll to one of the
Following options then press the Jog Wheel:
?
AT & T/ALCATEL
?
LINE REVERSAL
?
HIPATH
?
FSK/DTMF MWI
?
90V DC
?
ERICSSON MD-110
If Line Reversal is selected - Select Polarity Normal,
Polarity Reversal or OFF and then press the Jog Wheel
again. This should be set to OFF if Line Reversal is not
required.
For the other message waiting options - Select ON or
OFF and then press the Jog Wheel. They should be set to
OFF if not required. If Siemens Hicom/Hipath is
selected the Hicom Sensitivity switch (SW1) on the base
of the telephone should be set ‘Low’. At all other times
this should be switch to ‘High’.
•
Dial Mode
Scroll to 'DIAL MODE' on the System Menu and then
press the Jog Wheel. Select either Tone or Pulse
dialling then press the Jog Wheel again.
The default setting for the telephone is Tone dialling.
1. INSTALLATION
•
other end to the socket located in the bottom of the phone.
Replace the handset to the cradle.
NOTE: You will need to remove the wall mount
bracket to access this socket
.
•
Connect the small plug (RJ-11) of the telephone line
cord to the socket at the back of the unit and the other plug
to the telephone socket at the wall.
NOTE: If the RJ-11 to RJ-11 line cord is used, please
ensure that the Blue plug is connected to the wall socket.
•
Connect the AC adaptor into a standard 220-240VAC
mains socket and the power socket at the back of the NRX
EVO 450.
•
The display will show
00-00-00
. After about 4 seconds
the display will show
TOTAL:00 NEW:00
•
If you have subscribed to a Caller ID Service, the time
and date will be automatically updated when the first call
is received. Otherwise, it is necessary to set the time and
date manually, please refer to the Telephone Setup Menu.
Connect one end of the coil cord to the handset and the
In case of power failure or accidental unplugging of the
AC adaptor, the built-in EEPROM will retain all the
telephone's memory including phone book and CID
records.
1.2 Telephone Set-Up
In standby mode, press the
MENU
button twice, the
display will show
SYSTEM
.
Turning the jog wheel will switch among the various
setting modes of the Main System Menu loop as shown
below:
2
DIAL MODE
SET RECALL
LCD CONTRAST
SECURITY
MODE
SET TIME
MESSAGE
WAITING
AREA CODE
TIME MODE
PABX PREFIX
AUTOREDIAL
MODE
CLIP MODE
NEW ZEALAND
CLID
HS Auto Answer
