background image

8

GB

Insert the Front and Rear Pivot Brackets (21 and 

22) between the plastic and steel components of 

the table brackets and push until the steel tabs and 

notches engage (Fig 14). Note: these parts may 

be already pre-assembled. The small plastic stops 

must face inward, toward each other. Tighten the 

knobs.
Fit the Brace Struts (25) and Front and Rear Height 

Brackets (23 and 24) to the inside face of the pivot 

brackets using short M6 Screws (12), Nyloc Nuts 

(26) and Washers (7) (Figs. 15 and 16). The bolts 

prefitted to the height brackets locate in the slots 

on the pivot brackets. Two washers are used at 

each end - against the nut and inserted between 

the height adjustment bracket and brace strut (Fig. 

16).

Fit the brace with holes in it at the end furthest 

away from the table T-slots and fit both braces with 

the plastic toggles facing away from the T-slots 

(Fig 15).

Turn the table over and re-fit to the Workcentre.
Ensure the table brackets are fully located and 

tightened. Locate the braces with the toggles 

resting on the Workcentre base channel (Fig. 17). 

Loosen the nuts and adjust the toggle positions 

until the braces 'snap' down into place (Fig. 17) 

(inset).The correct position should support the table 

without lifting it. Re-tighten the nuts.

Fit Round Knobs (18) to the front and rear height 

adjustment brackets and lock them tilted outward 

slightly, for easy mounting of the planer chassis 

(Fig. 18).

Slide the planer chassis down between the 

brackets and insert a long Coach Bolt (27), as 

shown, through the square tubes at each end while 

supporting the chassis (Fig. 19).
Fit the Height Indicators (28) and Round Knobs (18) 

to the coach bolts (Fig. 20).

 

Lift the chassis to full height and tighten the round 

knobs. Loosen the pivot knobs and pivot the 

chassis vertical to the table then tighten  

(Fig. 21). 
Use a square to check that the planer blade is 90˚ 

to the table, as shown. If necessary, loosen the 

Assembly

Fig. 14

Fig. 15

Fig. 16

Fig. 17

Fig. 18

Fig. 19

Fig. 20

Summary of Contents for EPA 001












Reviews: