Tritech Intelligent Gyro Compass Page 6 Product Manual Download

Page: 6 / 50

Tritech International Ltd

Intelligent Gyro Compass

4.1

Technical Support And Software Upgrades

Contact your local agent or Tritech International Ltd



Mail

Tritech International Ltd.

Peregrine Road,
Westhill Business Park,
Westhill, Aberdeen,
AB32 6JL, UK



Telephone

++44 (0)1224 744111

Fax

++44 (0)1224 741771



[email protected]

Web

www.tritech.co.uk

An out-of-hours emergency number is available by

calling the above telephone number

If you have cause to use our Technical Support service, please ensure that you have the following
details at hand

prior

to calling:



iGC Assembly Part No.

iGC Serial No.



Operating mode settings (if known)

Firmware version (if known)



Fault Description



Details of other equipment used in the iGC system (e.g. iFG, iIF etc.)



Details of remedial action or faultfinding already implemented

It is worthwhile keeping a copy of this manual to hand, together with any system drawings showing how
the iGC connects to your system prior to making a call to the help-line. This will ensure that we can
diagnose the problem as quickly as possible.

Issue 2

0707-SOM-00004

Page 7 of 51

Summary of Contents for Intelligent Gyro Compass



















































Search results

Summary of Contents for Intelligent Gyro Compass

Reviews:

Related manuals for Intelligent Gyro Compass

Brands by name

Popular brands

Tritech Intelligent Gyro Compass, Product Manual

Search results

Summary of Contents for Intelligent Gyro Compass

Reviews:

Related manuals for Intelligent Gyro Compass

Brands by name

Popular brands