Tritech iGC Product Manual Download

Page: 52 / 52

Intelligent Gyro Compass (iGC)

0707-SOM-00004-7

© Tritech International Ltd.

Appendix H. iGC Recommended Spares

Item

Qty

Description

Part No.

Dome

SP-0013-101-001-01

End Cap

SP-0013-101-001-02

Sensor Assembly

SP-0013-101-003-00

iGC Interface PCB Assembly

SP-0013-101-002-00

Subconn 8-way micro bulkhead male

connector (SS)

MCBH8MSS

Subconn Locking sleeve

MCDLSF

Subconn connector 'O'-ring

SP-0013-101-001-00-7

'O'-ring

200-039

M2.5 mounting pillar

SP-0013-101-002-01

M3 mounting pillar

SP-0013-101-002-02

8 -way screw terminal connector

SP-0013-101-001-00-11

M3 x 6mm lg. Skt. head cap screw -

st. stl.

SP-0013-101-001-00-12

M3 spring washer - st. stl.

SP-0013-101-001-00-13

M2.5 x 6mm lg. Skt. head cap screw SP-0013-101-001-00-14

M2.5 plain washer

SP-0013-101-001-00-15

M3 x 10mm lg. Pan head pozi m/v

screw - st. stl.

SP-0013-101-001-00-16

TO-220 insilating bush

SP-0013-101-001-03

Insulating washer

SP-0013-101-001-04

2mm Jumper link (typ. red)

SP-0013-101-001-00-19

Silicone grease

111

Thread locking compound

222

Subconn Locking sleeve circlip

SP-0013-101-001-00-22

Identification / Serial No. Label

SP-0013-101-001-05

Processor module

SP-0013-101-001-06

M3 x 6mm lg. Pan head pozi m/c

screw - st. stl.

SP-0013-101-001-00-25

M3 red fibre washer

SP-0013-101-001-00-26

Heat-shrinkable wire ident markers

SP-0013-101-001-00-27

Bootlace ferrule 0.34mmsq

SP-0013-101-001-00-28

30mm length 4.8mm clear heatshrink SP-0013-101-001-00-29

100mm lg. Cable tie

SP-0013-101-001-00-30

Notes:

1. Spares are available from Tritech by quoting BOM and item number

2. Refer to Recommended Spares List for cross-reference

3. To maintain warranty and get the best performance from the iGC, only use genuine spare

parts

Summary of Contents for iGC





















































Search results

Summary of Contents for iGC

Reviews:

Related manuals for iGC

Brands by name

Popular brands

Tritech iGC, Product Manual

Search results

Summary of Contents for iGC

Reviews:

Related manuals for iGC

Brands by name

Popular brands