Tripp Lite SmartRack SR42UBEIS Owner'S Manual Download

Page: 13 / 13

Owner’s Manual Addendum

SmartRack

™

Side Panel Latch Installation

Important: Before installing the side panels, you must
install a latch (included) in each side panel.

Working from the outer surface of the side panel, insert

the upper portion of the latch into the side panel cutout as
shown.

Push the lower portion of the latch into the side panel

cutout as shown.

Snap the latch into place. The latch should be flush with

the outer surface of the side panel. Repeat the process for
each side panel.

Note: To install the side panels, follow the instructions in
the rack enclosure owner’s manual.

1111 W. 35th Street, Chicago, IL 60609 USA

773.869.1234 (USA) • 773.869.1212 (International)

www.tripplite.com

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Made in China.

200905072 • 932902-EN

ARRANTY

REGISTRA

TION:

y f

or a

chance to win a FREE

ipp Lite

product—www

.tr

ipplite

.com/w

arr

anty

Summary of Contents for SmartRack SR42UBEIS














Search results

Summary of Contents for SmartRack SR42UBEIS

Reviews:

Related manuals for SmartRack SR42UBEIS

Brands by name

Popular brands

Tripp Lite SmartRack SR42UBEIS, Owner'S Manual

Search results

Summary of Contents for SmartRack SR42UBEIS

Reviews:

Related manuals for SmartRack SR42UBEIS

Brands by name

Popular brands