Tripp Lite NGI-M08C4-L2 Owner'S Manual Download Page 182

Page: 182 / 313

182

6.12.2

Port Configuration

6.12.2.1

CLI Configuration

Node

Command

Description

enable

show pppoe intermediate-agent

configuration

This command displays the current

configurations for the PPPoE IA.

enable

configure terminal

This command changes the node to

configure node.

configure

interface IFNAME

This command enters the interface

configure node.

interface

pppoe intermediate-agent

<enable|disable>

This command disables / enables the PPPoE

IA on specific interface for the PPPoE IA.

interface

pppoe intermediate-agent trust

This command setsaphysical

interfaceastrusted port.

interface

pppoe intermediate-agent

format-type <circuit-id|remote-

id><id-string>

This command sets circuit ID or remote ID

string on specific interface for the PPPoE

IA.

interface

pppoe intermediate-agent

vendor-tag <keep|replace|strip>

This command is used to set the

retransmitting policy of the specific

interface for the PADO/PADS packet.

Default:Keep

interface

pppoe intermediate-agent vlan

VLANLISTS

This command enables thePPPoE IA on

specific VLANs of interface.

interface

no pppoe intermediate-agent

trust

This command setsaphysical interfaceas

untrusted port.

interface

no pppoe intermediate-agent

format-type <circuit-id|remote-

id>

This command removes circuit ID or remote

ID string on specific interface for the PPPoE

interface

no pppoe intermediate-agent

vendor-tag

The command sets the retransmitting policy

of the specific interface as “keep”.

interface

no pppoe intermediate-agent

vlan

This command disables thePPPoE IA on all

VLANs.

interface

no pppoe intermediate-agent

vlan VLANLISTS

This command disables thePPPoE IA on

specific VLANs of interface.

if-pppoe-vlan pppoe intermediate-agent

format-type <circuit-id|remote-

id><id-string>

This command sets circuit ID or remote ID

string on specific VLANs of interface for the

PPPoE IA.

if-pppoe-vlan no pppoe intermediate-agent

format-type <circuit-id|remote-

id>

This command removes circuit ID or remote

ID string on specific VLANs of interface for

the PPPoE IA.

Example:

L2SWITCH(config)#pppoe intermediate-agent enable

L2SWITCH(config)#pppoe intermediate-agent vlan 1-100,200,300

L2SWITCH(config)#pppoe intermediate-agent circuit-id-vlan 1-100,200,300

L2SWITCH(config)#pppoe intermediate-agent remote-id-vlan 1-100,200,300

L2SWITCH(config)#pppoe intermediate-agent format-type user-defined

%H%SPACE+atm+%SPACE+/0/0/+%PORT+:+%CVLAN

Summary of Contents for NGI-M08C4-L2


























































































































































































































































































































Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands

Tripp Lite NGI-M08C4-L2, Owner'S Manual

Search results

Summary of Contents for NGI-M08C4-L2

Reviews:

Related manuals for NGI-M08C4-L2

Brands by name

Popular brands