TriPoint PRODELIN 1892 Series Assembly Manual Download Page 5

4096-629

PRODELIN CORPORATION 

.89/.98M Ku-BAND Rx/Tx SERIES 1892/1982 

4

SECTION I     

INTRODUCTION

1.0

GENERAL INFORMATION

This manual describes the assembly and installation of Prodelin's .89/.98 meter 
antenna systems. The Prodelin .89/.98 meter is a rugged and reliable mount 
which will operate in the Ku-Band frequency with high efficiency and at the same 
time successfully  withstand the effects of the environment. Prodelin’s .89/.98 
Meter antennas have an F/D ratio of .8, an offset angle of 16°, and is commonly 
used with a 39° Prodelin Feed Horn. 

 

These instructions are listed by sections that cover all areas of assembly and 
installation.  Additional sections are included in the manual to provide information 
on antenna alignment to the satellite and maintenance. 

1.1

UNPACKING AND INSPECTION

The system containers should be unpacked and inspected at the earliest date to 
insure that all material has been received and is in good condition. A complete 
packing list for each major component is supplied. 

1.2

FREIGHT DAMAGE

Any damage to materials while in transit should be immediately directed to the 
freight carrier.  He will instruct you on matters regarding any freight damage 
claims.

1.3

MATERIAL – MISSING OR DAMAGED

Any questions regarding missing or damaged materials that are not due to the 
freight carrier should be directed to Prodelin's Customer Service Department at: 

 PRODELIN 

CORPORATION

1500 Prodelin Drive 

Newton NC 28658 

USA

 (828) 

464-4141

Summary of Contents for PRODELIN 1892 Series


















Reviews: