Triplett WiFi Hound Page 18 User Manual Download | Manualshive

Page: 18 / 32

background image

14

WiFi Hound

TM

User Manual

www.Triplett.com

4.3.6 Real Wave Labels

There are several additional items you can display alongside the SSID, including the Channel Number, Broadcast Type,
and MAC Address.

When to use the MAC ADDRESS option

When working in a campus environment, there will often be multiple Access Points (APs) that are broadcasting the
same SSID. (Imagine being at The Hotel LaGrande, and there is WiFi throughout the enormous, 20-story building. This
hotel could have a hundred APs, and all those APs would be broadcasting just one SSID – LaGrande_WiFi.) In order to
troubleshoot a specific Access Point, you must determine what the MAC Address is of that AP since the MAC Address
is the only unique identifier for an Access Point.

4.3.7 Interference Filters

Interference Filters will help you to see your target AP even in a heavily saturated wireless environment.

«
...
16
17
18
19
20
...
»

Summary of Contents for WiFi Hound

































Reviews:

No comments

Related manuals for WiFi Hound

Giraffe OmniBed

Brand: Ohmeda Pages: 54

Brand: Barreto Pages: 20

Brand: Barreto Pages: 18

Brand: Backyard Discovery Pages: 41

Brand: Gardena Pages: 8

Brand: GARANT Pages: 239

Brand: p-light Pages: 36

Brand: Hammer Strength Pages: 18

Brand: ParaBody Pages: 6

Brand: ParaBody Pages: 11

Brand: Valcom Pages: 6

Brand: Vaisala Pages: 60

Brand: VDO Pages: 15

Brand: VDO Pages: 20

Brand: Zimmer Pages: 2

Brand: ZipRip Pages: 31

Brand: ZOLL Pages: 48

Brand: Xtricity Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands