Tricity Bendix TBWD 1210 Operating & Installation Instructions Manual Download

Page: 12 / 32

5. Select the Spin speed or

Rinse hold option

Depress the

Spin

(speed) button to choose the required

speed or

Rinse hold

option: the corresponding light

illuminates.

6. Select the required options

The light corresponding to the depressed button
illuminates.

7. Select the Delay Start option

To delay starting of a programme, press the

Delay Start

button. The corresponding light illuminates. The figures
corresponding to the selected delay will be displayed for
about 3 seconds, after which the duration of the selected
programme will appear on the display.
When the

Start/Pause

button is pressed, the selected

delay will again appear on the display and the machine
starts its countdown.

Delay

start

Programme time

Prewash

Quick

Half

load

Extra

rinse

Rinse

hold

Spin

900
700
500

1200

During this period it is possible to load other laundry:
press the

Start/Pause

button. Open the door. Load the

laundry. Close the door and press the

Start/Pause

button again.

8. Start the programme

To start the selected programme, press the

Start/Pause

button; the corresponding light stops flashing and

the

Wash

pilot light illuminates

The pilot light corresponding to the wash phase which is
running is on.
The machine starts operating.

If the

Delay Start

option has been selected the

programme will start at the end of the countdown.

9. At the end of the programme

The machine stops automatically. The display shows a
blinking zero. The light of the

Start/Pause

button goes

out and the

End

light illuminates.

If the

Rinse hold

option has been selected, the door will

be locked, the

Rinse hold pilot

light

in the programme

progress display remains lit to indicate that the water
must be drained before opening the door. The display
shows a flashing zero.

To empty out the water you can after turning the
programme selector dial to

Off

position:

●

select

Drain

programme, the water is emptied out

without spinning

●

select

Spin

programme. Select the spin speed by

means of the relevant button and then depress the

Start/Pause

button. The water is emptied out and the

laundry is spun at the selected spin speed.

At the end of the cycle, the light of the

Start/Pause

button light goes out, and the

End

light

illuminates. The

door can be opened.

Turn the programme selector dial to Reset

Off

Start/

Pause

Summary of Contents for TBWD 1210

































Search results

Summary of Contents for TBWD 1210

Reviews:

Related manuals for TBWD 1210

Brands by name

Popular brands

Tricity Bendix TBWD 1210, Operating & Installation Instructions Manual

Search results

Summary of Contents for TBWD 1210

Reviews:

Related manuals for TBWD 1210

Brands by name

Popular brands