English version
Français au verso
For indoor use only.
Regularly check the cord, the transformer and all other parts for
damage. If any part is damaged, the lamp should not be used.
Protect the power cord from being walked on or pinched, particularly
at the plugs, convenience receptacles and the point where the power
cord exits the lamp.
Do not cut or shorten the power cord.
The lamp may in no way be modified or tampered with, any modification
may compromise its safety causing the product to become dangerous.
Trica declines all responsibility for products that are modified.
Avoid placing this lamp in areas exposed to heat-radiating products
such as heaters.
Lift the lamp by its metal base, not by the wood part or shade.
Never cover the lamp or place anything on top of it.
This product requires the use of the supplied 12 VDC power supply.
Do not use with power supply voltage other than 120 VAC.
Do not use the lamp with light dimmers (other than the one supplied
with this lamp), timers or motion detectors.
To avoid damaging the lamp, do not position its base in a way that
compromises the stability of the lamp or renders it unable to stay
upright.
Closely supervise children who are using this lamp or are near it, as
well as others who may not understand the need for these precautions.
WARNING
Deviation from the assembly instructions may result in a risk of fire
or electric shock.
To avoid electrocution, do not operate this lamp near water.
CAUTION
The light source of this product is non-changeable light diodes (LED)
with a life span of 75 000 hours. Do not disassemble the product, as
the light diodes can cause damage to the eyes.
CLEANING
Your lamp is made from high-quality materials that will last for
many years with minimum care. You may want to periodically clean
the lamp, using a mild non-abrasive cleaner and soft damp cloth.
When cleaning, make sure you have turned off and unplugged the
lamp. After cleaning the lamp, properly wipe away and dry all moisture
before restoring power.
DO NOT USE SOLVENTS OR CLEANERS CONTAINING ABRASIVES, OR
AMMONIA-BASED CLEANERS ON THIS PRODUCT.
DO NOT IMMERSE IN WATER.
WARRANTY FOR RESIDENTIAL USE
TRICA’s products have a 10-year limited warranty covering any metal
structure defect or any defect in fabrication resulting from human
error. Electrical components are covered under a 5-year warranty.
External features, fabric coverings and seams are covered under a
1-year limited warranty for any fabrication defect. The paint finishes
and the normal wear and tear of the components mentioned above
are not covered under this warranty.
LIABILITY DISCLAIMERS
Trica shall not be liable for loss of use of the products or for any
consequential, indirect, special or incidental costs, expenses, damages,
personal injury, death or other loss incurred by the consumer and
resulting from the Trica products, including, without limitation:
• Leaving children without supervision near or using the Trica product.
• Neglectful, unreasonable, careless or unsafe use of the Trica
products.
IMPORTANT SAFETY INSTRUCTIONS
TOUCH DIMMER SWITCH OPERATION
www.tricafurniture.com
Powered by/ Illuminé par
This product uses a certified power and lighting system
Ce produit utilise un système électro-lumineux certifié.
Conforms to UL STD 2108
Certified to CSA STD C22.2 No. 250.0
Model No.
BEAM
Your fixture is equipped with a touch dimmer switch. It
allows you to turn on, turn off and dim the fixture. It is
also equipped with a soft start / stop feature; it is then
normal that it takes a few seconds to reach maximum
intensity and complete off.
- Touch once to turn on.
- Touch and hold to decrease intensity and release once desired level
is reached.
- Touch and hold again to increase intensity and release once
desired level is reached.
- Touch once to turn off.
NOTE1:
The last intensity level selected will be kept in memory when you
turn the light off.
NOTE2:
The intensity level range goes from 100% to 0%. If you dim the fixture
completely until it looks off, you need to touch and hold switch again
to increase intensity back to 100%.
NOTE3:
To reset switch memory, simply unplug power cord for a few seconds.
