background image

Vent/Air System Installation

6

Do  not  over  tighten  the  self-drilling  screws

into  the  sections.  Use  a  low  torque  screw

drive to prevent stripping out the holes. If a

hole becomes stripped due to over tightening,

a  larger  diameter  screw  (length  of  screw

must  not  exceed  1/2”)  or  a  short  pop  rivet

may be used.

6. Seal the two components together by placing a

clamp  over  the  connection  and  pressing  down
on the clamp lever.  The clamp should be cen-
tered  over  the  connection  and  the  edge  of  the
clamp should cover the beads on the end of each
component.  If  the  clamp  does  not  cover  and
lock  onto  the  component  jacket  beads,  ensure
the  components  are  fully  pressed  together  and
interlocked

WARNING

It is very important that the clamp be prop-
erly  installed.    Failure  to  properly  connect
the vent components could lead to vent fail-
ure and can result in death, serious injury or
substantial property damage.

Termination Installation

1. Determine  the  termination  location  using  the

guidelines listed on page 4 and 5 and drill or cut
a 6 inch hole.

2. Install  the  interior  support  plate  on  the  inside

wall using the screws provide in the kit.

3. Mount the termination fitting through the interi-

or  support  plate  from  the  exterior  side  of  the
wall.  Ensure  the  air  inlet  holes  of  the  termina-
tion fitting are facing down and that the fitting
is mounted level.

To  determine  the  appropriate  length  of  the
termination  fitting,  mount  the  exterior  sup-
port plate temporarily prior to the installation
of the interior support plate. Insert the termi-
nation fitting from the interior side of the wall
through the exterior support plate. The termi-
nation fitting has a formed bead that limits the
distance  of  penetration  through  the  exterior
support plate. The termination fitting should
be measured and cut to length prior to mount-
ing  the  support  plates.  For  information  on
measuring and cutting the termination fitting,
reference page 7.

4. Mount the exterior support plate around the ter-

mination on the outside wall. Ensure the support
plate is flush to the formed end of the termina-
tion fitting and the fitting is mounted level.

The  termination  fitting  must  be  installed
level  without  pitch  to  either  the  boiler  or
away from boiler. 

NOTICE

NOTICE

WARNING

Clamp 

Female

End

Male End

Outer Jacket

Bead

Inner Pipe

Gasket

Lever

Fig. 7:  Vent Joint Assembly

Note: 

Secure  outer  sections  together  where  they

overlap with 2 self-drilling screws provided, 90º
apart using low torque setting of driver.

Summary of Contents for Prestige Solo 399













Reviews: