BEEPER PLACEMENT
ON THE COLLAR STRAP
Adjust the position of the Beeper on the
collar strap for the size of your dog, taking
into account where you want the buckle
to be located. The proper placement of
the Beeper is on top of the dog’s neck.
(see figure 1)
POWER/MODE SELECT BUTTON
The black Power/Mode Select button, located on the top of the Beeper base,
serves both as an on/off switch and allows you to select the settings of the
Beeper.
SWITCHING THE BEEPER ON and OFF
(see figure 2&3)
1
.
To switch the Beeper on press the black Power/Mode Select button.
The RED LED indicator light will quickly turn on and then go out.
Release the button when the light goes out. A LOW-high tone
confirms that the Beeper has been turned on.
•
When the Beeper is switched on it will operate under the
last mode selected.
•
The indicator light will then continue to blink which confirms
the Beeper is on.
•
The factory default setting is a single beep for HUNT mode
and the hawk scream for POINT mode.
2
.
To switch the Beeper off press the button and hold it down until the
RED LED light goes off then let go immediately.
•
A HIGH-low tone confirms that it has been turned off.
•
To conserve battery life switch the Beeper off when not in use.
AVAILABLE MODES
(Sound Combinations)
The Upland G3 Beeper can operate under a variety of sound combinations
or “Modes”. These include various series of beeps when the dog is hunting
and a hawk scream or a beep when on point.
•
HUNT Mode – The Beeper sounds every 4 seconds while
the dog is moving.
•
POINT Mode – The Beeper sounds once every second while the dog is
on point. The hawk scream sounds every five seconds.
•
HUNT Mode and POINT Mode can be used in eight (8) pre-set
combinations that you select and set as described below.
•
To check the current Beeper setting - First switch the Beeper on.
Gently shake the Beeper (to simulate a running dog) and listen for the
HUNT setting. Next, hold the Beeper still and listen for the POINT
setting. Your new Beeper is LOUD!! Holding your thumb over
the speaker horn will lessen the sound.
CHANGING MODES
Both Modes (HUNT and POINT) are selected by using the Power/Mode
Select button. Press this button, and your sound selection will be indicated
by the blinking of each LED light. The RED LED light indicates the “HUNT”
setting and the GREEN LED light indicates the “POINT” setting.
figure 1
To change sounds you will need to cycle through the various options by
pressing the button and observing the series of blinks from the RED and
GREEN LED lights (see figure 3):
1.
Make sure that the Beeper power has been switched on.
2.
Press & hold the Power/Mode Select button until both LED lights
blink three (3) times together and then release the button.
3.
The LED lights indicate the current setting.
4.
You can now select the sound you prefer.
5.
To choose a mode, briefly press the button and the Mode will change
as indicated by the LED lights. Each time you press and release the
button, the lights will indicate a new setting. (You may have to cycle
through several settings to reach your preference. Be patient, check
the blinking of the LED lights after each button press, and continue
to briefly press the button.) See the Mode Setting Cycle chart below.
Mode Setting Cycle
As you cycle through the settings, 1-8, the order will occur as follows:
To SAVE your selection:
•
Press & hold the Power/Mode Select button until both
LED lights flash three (3) times together then release the button.
The Beeper will now operate in the Modes you have selected.
HUNT MODE - Red LED Light
You may select one of four settings as your HUNT Mode: Single Beep, Double
Beep, Triple Beep, or No Beep. While hunting with several dogs at once, the
various HUNT modes will come in handy for you to distinguish each dog.
Number of times the Red LED light blinks during selection:
•
Single Beep –
1
blink of Red LED
•
Triple Beep –
3
blinks of Red LED
•
Double Beep –
2
blinks of Red LED
•
No sound – No light
SETTING
#
POINT Mode
(Green LED)
HUNT Mode
(Red LED)
1
Solid (Hawk Scream)
1 blink (1 Beep)
2
Solid (Hawk Scream)
2 blinks (2 Beeps)
3
Solid (Hawk Scream)
3 blinks (3 Beeps)
4
Solid (Hawk Scream)
No light (No Beep)
5
Blinking (1 Beep)
1 blink (1 Beep)
6
Blinking (1 Beep)
2 blinks (2 Beeps)
7
Blinking (1 Beep)
3 blinks (3 Beeps)
8
Blinking (1 Beep)
No light (No Beep)
Power/Mode
Select Button
figure 2
RED & GREEN LED
Light Indicators
figure 3
RESET TO DEFAULT MODE SETTING (Setting #1)
If you should perhaps need to get the Beeper back to a known base
setting it is easy, no matter what mode the Beeper is in or if it is switched
on or off.
Just press and hold the Power/Mode Select button for at least 15
seconds. There will be high-low, high-low beeps, the LED lights will flash,
and the Beeper will switch off. When you switch the Beeper back on
it is now back to mode setting #1, the Hawk Scream for Point and one
beep for Hunt.