TRENDnet TV-IP325PI User Manual Download Page 41

TRENDnet User’s Guide 

 

TV‐IP325PI 

© Copyright 2018 TRENDnet. All Rights Reserved.

   

41

 

 Limited Warranty 

TRENDnet warrants its products against defects in material and workmanship, under 
normal use and service, for the following lengths of time from the date of purchase. 

TV‐IP325PI – 3 Years Warranty 

If a product does not operate as warranted during the applicable warranty period, 
TRENDnet shall reserve the right, at its expense, to repair or replace the defective 
product  or  part  and  deliver  an  equivalent  product  or  part  to  the  customer.  The 
repair/replacement unit’s warranty continues from the original date of purchase. All 
products that are replaced become the property of TRENDnet. Replacement products 
may  be  new  or  reconditioned.  TRENDnet  does  not  issue  refunds  or  credit.  Please 
contact the point‐of purchase for their return policies. 

TRENDnet  shall  not  be  responsible  for  any  software,  firmware,  information,  or 
memory data of customer contained in, stored on, or integrated with any products 
returned to TRENDnet pursuant to any warranty. 

There are no user serviceable parts inside the product. Do not remove or attempt to 
service the product by any unauthorized service center. This warranty is voided if (i) 
the product has been modified or repaired by any unauthorized service center, (ii) 
the  product  was  subject  to  accident,  abuse,  or  improper  use  (iii)  the  product  was 
subject to conditions more severe than those specified in the manual. 

Warranty  service  may  be  obtained  by  contacting  TRENDnet  within  the  applicable 
warranty  period  and  providing  a  copy  of  the  dated  proof  of  the  purchase.  Upon 
proper submission of required documentation a Return Material Authorization (RMA) 
number  will  be  issued.  An  RMA  number  is  required  in  order  to  initiate  warranty 
service support for all TRENDnet products. Products that are sent to TRENDnet for 
RMA service must have the RMA number marked on the outside of return packages 
and sent to TRENDnet prepaid, insured and packaged appropriately for safe shipment. 
Customers shipping from outside of the USA and Canada are responsible for return 
shipping  fees.  Customers  shipping  from  outside  of  the  USA  are  responsible  for 
custom charges, including but not limited to, duty, tax, and other fees. 

WARRANTIES  EXCLUSIVE:  IF  THE  TRENDNET  PRODUCT  DOES  NOT  OPERATE  AS 
WARRANTED  ABOVE,  THE  CUSTOMER’S  SOLE  REMEDY  SHALL  BE,  AT  TRENDNET’S 
OPTION,  REPAIR  OR  REPLACE.  THE  FOREGOING  WARRANTIES  AND  REMEDIES  ARE 
EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, 
EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 

TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME 
FOR  IT  ANY  OTHER  LIABILITY  IN  CONNECTION  WITH  THE  SALE,  INSTALLATION 
MAINTENANCE OR USE OF TRENDNET’S PRODUCTS. 

TRENDNET  SHALL  NOT  BE  LIABLE  UNDER  THIS  WARRANTY  IF  ITS  TESTING  AND 
EXAMINATION  DISCLOSE  THAT  THE  ALLEGED  DEFECT  IN  THE  PRODUCT  DOES  NOT 
EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, 
IMPROPER  INSTALLATION  OR  TESTING,  UNAUTHORIZED  ATTEMPTS  TO  REPAIR  OR 
MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY 
ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD. 

LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO 
EXCLUDES  FOR  ITSELF  AND  ITS  SUPPLIERS  ANY  LIABILITY,  WHETHER  BASED  IN 
CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, 
INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE 
OR  PROFITS,  LOSS  OF  BUSINESS,  LOSS  OF  INFORMATION  OR  DATE,  OR  OTHER 
FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, 
MAINTENANCE,  USE,  PERFORMANCE,  FAILURE,  OR  INTERRUPTION  OF  THE 
POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, 
OR  REFUND  OF  THE  PURCHASE  PRICE  PAID,  AT  TRENDNET’S  OPTION.  THIS 
DISCLAIMER  OF  LIABILITY  FOR  DAMAGES  WILL  NOT  BE  AFFECTED  IF  ANY  REMEDY 
PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. 

Governing Law: This Limited Warranty shall be governed by the laws of the state of 
California. 

Some TRENDnet products include software code written by third party developers. 
These codes are subject to the GNU General Public License (“GPL”) or GNU Lesser 
General Public License (“LGPL”). 

Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section 
and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. 
These codes are distributed WITHOUT WARRANTY and are subject to the copyrights 
of  the  developers.  TRENDnet  does  not  provide  technical  support  for  these  codes. 
Please go to http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/ 

lgpl.txt for specific terms of each license. 

 

 

 

7.20.17 

TV‐IP325PI 1.1 

Summary of Contents for TV-IP325PI











































Reviews: