TRENDnet TFM-560PCI, User Manual

Page: 18 / 44

I101 V.90 PCI MODEM USER'S MANUAL
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
44
P.18
3 Selects auto reliable mode and forces &Q5 (the modem will try to negotiate an error corrected link).
This operates the same as \N2 except failure to make a reliable connection results in the modem falling
back to the speed buffered normal mode.
4 Selects LAPM error-correction mode and forces &Q5 (the modem will try to negotiate an error cor-
rected link). Failure to make an LAPM error-correction connection results in the modem hanging up.
5 Selects MNP error-correction mode and forces &Q5 (the modem will try to negotiate an error cor-
rected link). Failure to make an MNP error-correction connection results in the modem hanging up.
A3.2.1.3 &F - Set to Factory-Defined Configuration
This command instructs the modem to set all parameters to factory default values defined in the product Configu-
ration Table. The modem loads the factory default configuration (profile). The factory defaults are identified for each
command and in the S-Parameter descriptions. A configuration (profile) consists of a subset of S-Parameters.
A3.2.1.4 &T [<value>] - Local Analog Loopback Test
The modem will perform the local analog loopback test if &T1 is selected. The test can be run only when in an
asynchronous operation in non-error-correction mode (normal). To terminate the test in progress, the escape se-
quence must be entered first. If S18 is non-zero, the test will terminate automatically after the time specified by S18 and
the OK result code will be reported.
Defined Values
<value> Decimal number corresponding to the selected value.
0 Terminates test in progress.
1 Initiates local analog loopback, V.54 Loop 3. If a connection exists when this command is issued, the
modem hangs up. The CONNECT XXXX message is displayed upon the start of the test.
A2.2.1.5 I [<value>] - Request Identification Information
This command causes the modem to report one or more lines of product information text as provided by the
Product Configuration File, as selected by the <value> subparameter, followed by a final result code.
Defined Values
<value> Decimal number corresponding to the selected information.
0 <value> 0 report.
…
7 <value> 7 report.
9 <value> 9 report.
A2.2.1.6 +GMI - Request Manufacturer Identification
This command causes the modem to report the modem product manufacturer as provided by the Product
Configuration File.
A2.2.1.7 +GMM - Request Model Identification
This command causes the modem to report the modem product model as provided by the Product Configuration
File.