TRENDnet TEW-651BR User Manual Download Page 77

Page: 77 / 80

TECHNICAL SPECIFICATIONS

Hardware

Standards

IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-TX), IEEE 802.3az (draft 2.0),
IEEE 802.11b, IEEE 802.11g, Based on IEEE 802.11n technology

WAN

1 x 10/100Mbps Auto-MDIX WAN port (Internet)

LAN

4 x 10/100Mbps Auto-MDIX LAN port

WPS Button

Enables Wi-Fi Protected Setup (WPS) function

Connection Type

Dynamic IP, Static (fixed) IP, PPPoE, PPTP, L2TP

Supported Web Browsers

Internet Explorer 6.0 or above, Firefox, Safari

Internet Access Control

MAC Address Filter, Domain/URL Filter, Protocol/IP Filter

SNMP

Up to 3 external trap receivers

LED Indicators

Power, Status, LAN1 - LAN4, WAN, WLAN

Power Switch

On/Off power switch

Power Supply

5V DC, 1A external power adapter

Power Consumption

2.8 watts (max)

Dimensions (LxWxH)

149 x 109 x 29mm (5.9 x 4.3 x 1.1in)

Weight

221g (7.8oz)

Temperature

Operating: 0° ~ 40°C (32° ~ 104°F)
Storage: -10°C ~ 70°C (-14° ~ 158°F)

Humidity

10% ~ 95% max (non-condensing)

Certifications

CE, FCC

Wireless

Frequency

2.412 ~ 2.484 GHz ISM band

Antenna

1 x 2dBi fixed dipole antenna

Module Technique

802.11b:

CCK

(11

and

5.5Mbps),

DQPSK

(2Mbps),

DBPSK

(1Mbps)

802.11g: OFDM with BPSK, QPSK and 16/64-QAM

802.11n: BPSK, QPSK, 16QAM, 64QAM with OFDM

Media Access Protocol

CSMA/CA with ACK

Data Rate
(Auto Fallback)

802.11b: up to 11Mbps
802.11g: up to 54Mbps
802.11n: up to 150Mbps

Output Power

802.11b: 15dBm (typical) @ 11Mbps
802.11g: 15dBm (typical) @ 54Mbps
802.11n: 13dBm (typical) @ 150Mbps

Receiving Sensitivity

802.11b: -85dBm (typical) @ 11Mbps
802.11g: -68dBm (typical) @ 54Mbps
802.11n: -62dBm (typical) @ 150Mbps

Encryption

64/128-WEP, WPA-PSK/WPA2-PSK, WPA/WPA2-RADIUS

Channels

1-11 (FCC), 1-13 (ETSI)

Summary of Contents for TEW-651BR

















































































Search results

Summary of Contents for TEW-651BR

Reviews:

Related manuals for TEW-651BR

Brands by name

Popular brands

TRENDnet TEW-651BR, User Manual

Search results

Summary of Contents for TEW-651BR

Reviews:

Related manuals for TEW-651BR

Brands by name

Popular brands