Traxxas Slash VXL 58076-3 Owner'S Manual Download Page 5

SLASH VXL • 5

SAFETY PRECAUTIONS

LiPo Batteries

Lithium Polymer (LiPo) batteries are becoming popular for use 
in R/C models due to their compact size, high energy density, 
and high-current output. However, these types of batteries 
require special care and handling procedures for long life and 
safe operation. 

WARNING: LiPo batteries are intended only for 

advanced users that are educated on the risks associated with 
LiPo battery use. Traxxas does not recommend that anyone 
under the age of 14 use or handle LiPo battery packs without the 
supervision of a knowledgeable and responsible adult. 

Your model is able to use LiPo batteries with nominal voltage not 
to exceed 11.1 volts (3S packs). LiPo batteries have a minimum 
safe discharge voltage threshold that should not be exceeded. The 
Velineon VXL-3s electronic speed control is equipped with built-in 
Low-Voltage Detection that alerts the driver when LiPo batteries 
have reached their minimum voltage (discharge) threshold.

 

It is the 

driver’s responsibility to stop immediately to prevent the battery 
pack from being discharged below its safe minimum threshold.

Low-Voltage Detection on the speed control is just one part of a 
comprehensive plan for safe LiPo battery use.

 

It is critical for you, 

the user, to follow all other instructions supplied by the battery 
manufacturer and the charger manufacturer for proper charging, 
use, and storage of LiPo batteries. Do not attempt to charge LiPo 
batteries with the Traxxas charger included in this package. Make 
sure you understand how to use your LiPo batteries. 

Be aware 

that Traxxas shall not be liable for any special, indirect, incidental, 
or consequential damages arising out of the installation and/or use 
of LiPo batteries in Traxxas models. 

If you have questions about 

LiPo battery usage, please consult with your local hobby dealer 
or contact the battery manufacturer. 

As a reminder, all batteries 

should be recycled at the end of their useful life. 

DO NOT ATTEMPT TO CHARGE LIPO BATTERIES OR ANY OTHER 
TYPE OF BATTERY WITH THE INCLUDED TRAXXAS CHARGER.

Speed Control

• Disconnect the Batteries

: Always disconnect the battery pack 

from the speed control when not in use. 

• Transmitter on First:

 Switch on your transmitter first before 

switching on the speed control to prevent runaways and erratic 
performance.

• Don’t Get Burned

: The heat sink can get extremely hot, so be 

careful not to touch it until it is cool. Supply adequate airflow for 
cooling.

• Use Stock Connectors

: If you decide to change the battery or 

motor connectors, only change one battery or motor connector at 
a time. This will prevent damage from accidentally mis-wiring the 
speed control. Please note that modified speed controls can be 
subject to a rewiring fee when returned for service. Removing the 
battery connector on the speed control or using the same-gender 
connectors on the speed control will void the product’s warranty.

• Insulate the Wires

: Always insulate exposed or damaged wiring 

with heat shrink tubing to prevent short circuits

Summary of Contents for Slash VXL 58076-3



































Reviews: