5581
5128
X-ring
5579
5119
10x15x4BB
5119
10x15x4BB
2524
2.5x8CCS
5579
5125
5127
5128
5126
5125
5128
5125
5128
E-clip
5125
5128
E-clip
5582
5581
5128
5128
5128
5582
5x10x0.5PTW
5581
5128
X-ring
5582
5x10x0.5PTW
5125
5128
E-clip
5125
5581
5128
X-ring
5579
5119
10x15x4BB
5119
10x15x4BB
2524
2.5x8CCS
5579
5125
5127
5128
5126
5125
5128
5125
5128
E-clip
5125
5128
E-clip
5582
5581
5128
5128
5128
5582
5x10x0.5PTW
5581
5128
X-ring
5582
5x10x0.5PTW
5125
5128
E-clip
5125
Install the differential and driveshafts
16. Insert both axles through the
bearings located in the stub
axle carriers one at a time (Q),
and place the differential back
into the transmission (see “R”
for correct orientation).
17. Attach the differential cover to the back of the transmission. Make
sure that the suspension pins are in the blue rear toe plate, and
secure the cover with two 3x15 countersunk machine screws
(S1) and two 3x10 button-head machine screws (S2). Secure the
battery cover to the battery holder with four 2.5x10 cap-head
machine screws (S3).
18. Attach the rear shocks to the suspension
arms with two 3x18 button-head machine
screws and to the shock tower with two
3x15 button-head machine screws (T).
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected]
S1
S2
S3
T
19. Insert the axle pins into the holes in the
axles, and slide the hex hubs onto the
axles (U). Attach the wheels on the hex
hubs. Make sure the hex hubs are keyed
into the wheels and secure the wheels
with two 4.0mm nylon locknuts.
Steel CV driveshaft maintenance
The driveshafts are lubed and sealed at the factory and are built to
last. While the maintenance intervals are much larger with the sealed
shaft joints, it is still important to provide regular maintenance to
ensure long life. Follow the steps below for proper maintenance:
After every gallon of fuel*:
1. Pull the dust boots toward the middle of the shaft to inspect and
clean the inner and outer shaft joints. Clean the joints and dust
boots with denatured alcohol.
2. Inspect the drive cups, driveshafts, and dust boots for wear.
3. Lube the driveshaft joints with Traxxas thrust bearing lube (Part
#2717).
4. Push the dust boots back over the joints. Make sure the boots fit
snug around the joint.
* If running in sandy or dusty conditions, perform these steps after every half gallon.
R
Differential Assembly
Driveshaft Assembly
If you have questions or need technical assistance, call Traxxas at
1-888-TRAXXAS
(1-888-872-9927) (U.S. residents only)
5125
Drive cups, inner (2) (for steel constant-velocity
driveshafts)/ differential spider gears (2)/
gaskets, hardware ............................................. $15.00
5126
Driveshaft, steel constant-velocity, (shaft only)/
drive cup pin (1) ....................................................$9.50
5127
Stub axle (1) (for steel constant-velocity
driveshaft) ................................................................$6.00
5128
Rebuild kit (for Jato steel constant-velocity
driveshafts) (includes pins, dustboots, gaskets,
e-clips, x-rings, lube, and hardware for 2
driveshaft assemblies).... .................................. $10.00
Q
U
