background image

14 

 E-Revo

Don’t push the transmitter 
antenna down from the 
top. Pull it down from the 
bottom, one segment at a 
time, to prevent binding and 
kinking the antenna mast.

TQ Radio System Adjustments

In addition to the electronic throttle and steering trim controls, 
your radio system features throttle neutral adjustment and servo 
reversing switches. 

These are preset at the factory and should 

not require further adjustment.

Throttle Neutral Adjustment

The throttle neutral adjustment is located on the transmitter face 
and controls the forward/reverse travel of the throttle trigger. 
Change the adjustment by pressing the button and sliding it to 
the desired position. 

There are two settings available:

50/50:

  Allows equal travel for both 

acceleration and reverse. 

70/30:

  Allows more throttle travel (70%) 

and less reverse travel (30%).

Note:

 If you change throttle travel, you  

will need to reprogram the electronic 
speed control.

Electronic Throttle Trim

The electronic throttle trim located on the face of the transmitter 
adjusts the neutral (center) point of the electronic speed control. 
This control has been preset for you at the factory. 

Electronic Steering Trim

The electronic steering trim located on the face of the transmitter 
adjusts the neutral (center) point of the steering servos when the 
servos are at rest. Adjust this control to make the model drive 
straight with no steering input at the wheel. 

Servo Reversing Switches

The servo reversing switches are located on the front of the 
transmitter, next to the on/off switch. Moving a switch reverses 
the direction of the corresponding servo.

Each switch corresponds to a channel, as shown below. For 
example, if you turn the steering wheel to the right and your  
wheels turn left, you would move the Channel 1 switch to 
correct the servo direction. It may be necessary to adjust the 
corresponding trim control after moving a switch.

TQ Radio System Controls

Steering

TU

R

N

 L

EF

TU

R

N

 R

IG

H

Brake/Reverse

Neutral

Accelerate

CH.2

CH.1

CH.2

CH.1

CH.2

CH.1

Channel

1

2

Servo

Steering

Throttle

Default Setting

The Traxxas TQ Radio System

Summary of Contents for E Revo 5605

































Reviews: