TRAXXAS • 13
TRAXXAS TQ
i
RADIO SYSTEM
7
Range-Testing the Radio System
Before each running session with your model, you should range-test
your radio system to ensure that it operates properly.
1. Turn on the radio system and check its operation as described in
the previous section.
2. Have a friend watch the model. Make sure hands and clothing are
clear of the wheels and other moving parts on the model.
3. Walk away from the model with the transmitter until you reach
the farthest distance you plan to operate the model.
4. Operate the controls on the transmitter once again to be sure
that the model responds correctly.
5. Do not attempt to operate the model if there is any problem with
the radio system or any external interference with your radio
signal at your location.
Higher Speeds Require Greater Distance
The faster you drive your model, the more quickly it will near the
limit of radio range. At 60mph, a model can cover 88 feet every second!
It’s a thrill, but use caution to keep your model in range. If you want to
see your model achieve its maximum speed, it is best to position yourself
in the middle of the model’s running area, not the far end, so you drive
the model towards and past your position. In addition to maximizing the
radio’s range, this technique will keep your model closer to you, making
it easier to see and control.
Your model’s radio system is designed to operate reliably up to the
approximate distance that it is no longer easy or comfortable to see and
control the model. Most drivers will struggle to see and drive their model
at distances farther than a football field (300+ feet). At greater distances,
you could lose sight of your model and you may also exceed the radio
system’s operating range, which will cause the failsafe system to activate.
For best visibility and control of your model, keep your model within 200
feet, regardless of the maximum range available.
No matter how fast or
far you drive your model, always leave adequate space between you,
the model, and others. Never drive directly toward yourself or others.
TQi Binding Instructions
For proper operation, the transmitter and receiver must be
electronically ‘bound.’
This has been done for you at the factory.
Should you ever need to re-bind the system or bind to an additional
transmitter or receiver, follow these instructions.
Note:
The receiver
must be powered on for binding and the transmitter and receiver
must be within 5 feet of each other.
1. Press and hold the transmitter’s SET button as you switch the
transmitter on. The transmitter’s LED will flash red slowly.
2. Press and hold the receiver’s LINK button as you switch on the
speed control by plugging a battery into it.
3. When the transmitter and receiver’s LEDs turn solid green, the
system is bound and ready for use. Confirm that the steering and
throttle operate properly before driving your model.
Setting up the Antenna
The receiver antenna has been set up
and installed from the factory. The
antenna is secured by a 3x4mm set
screw. To remove the antenna tube,
simply remove the set screw with the
included 1.5mm wrench.
When reinstalling the antenna, slide the
wire into the bottom of the tube until
the white tip of the antenna is at the
top of the tube under the black cap. Next, insert the tube into the
mount, making sure the antenna wire is in the slot in the antenna
mount. Install the set screw next to the antenna tube. Use a 1.5mm
wrench to tighten the screw. Do not over-tighten. Do not bend or
kink the antenna wire or shorten the antenna tube.
Using Reverse: While driving,
push the throttle trigger
forward to apply brakes.
Once stopped, return the
throttle trigger to neutral.
Push the throttle trigger
forward again to engage
proportional reverse.
Automatic Failsafe
The TQi transmitter
and receiver are equipped
with an automatic failsafe
system that does not require
user programming. In
the event of signal loss or
interference, the throttle
will return to neutral and
the steering will hold its
last commanded position. If
failsafe activates while you
are operating your model,
determine the reason for
signal loss and resolve the
problem before operating
your model again.
In order to re-acquire the
signal after the failsafe has
activated, you will need to
walk a longer distance closer
to the model than the distance
the model travelled out of
range. Simply keep walking
towards the model until you
re-acquire the signal.
RADIO SYSTEM CONTROLS
Antenna
Tip
Antenna
Tube
