background image

14 • SLASH  4x4

RADIO SYSTEM RULES 

• Always turn your TQi transmitter on first and off last. This procedure 

will help to prevent your model from receiving stray signals from 
another transmitter, or other source, and running out of control. Your 
model has electronic fail-safes to prevent this type of malfunction, 
but the first, best defense against a runaway model is to always turn 
the transmitter on first and off last.

• Always use new or freshly charged batteries for the radio system. 

Weak batteries will limit the radio signal between the receiver 
and the transmitter.

 Loss of the radio signal can cause you to lose 

control of your model.

• In order for the transmitter and receiver to bind to one another,  

the receiver in the model must be turned on within 20 seconds 
of turning on the transmitter. The transmitter LED will flash fast 
red, indicating a failure to link. If you miss it, simply turn off the 
transmitter and start over.

• Always turn on the transmitter before plugging in the battery.

RADIO SYSTEM BASIC ADJUSTMENTS

Throttle Neutral Adjustment 

The throttle neutral adjustment is located 
on the transmitter face and controls the 
forward/reverse travel of the throttle trigger. 
Change the adjustment by pressing the 
button and sliding it to the desired position. 
There are two settings available:

50/50

: Allows equal travel for both 

acceleration and reverse.

70/30

: Allows more throttle travel (70%) and less reverse travel (30%).

Note: We strongly recommend to leave this control in its factory 
location until you become familiar with all the adjustments and 
capabilities of your model. 

To change the throttle neutral adjust 

position, turn the transmitter off before adjusting the neutral 
position. 

You will need to reprogram your electronic speed control 

to recognize the 70/30 setting.

 Turn to ESC Setup Programming on 

page 17 for instructions.

Steering Trim 

The electronic steering trim located on the 
face of the transmitter adjusts the neutral 
(center) point of the steering channel. 

Note: 

Traxxas Stability Management (TSM) must be completely 

turned off while adjusting steering trim. See page 16 for TSM 
adjustments.

Multi-Function Knob

The multi-function knob can be programmed 
to control a variety of functions. From the 
factory, the Multi-Function knob controls 
Traxxas Stability Management (TSM). For 
more detail on TSM, refer to page 16.

TRAXXAS TQ

i

 RADIO & VELINEON POWER SYSTEM

Remember, always turn the 
TQi transmitter on first and 
off last to avoid damage to 
your model. 

Automatic Fail-Safe

The TQi transmitter and 
receiver are equipped 
with an automatic fail-
safe system that does not 
require user programming. 
In the event of signal loss 
or interference, the throttle 
will return to neutral and 
the steering will hold its last 
commanded position. If the 
Fail-Safe activates while you 
are operating your model, 
determine the reason for 
signal loss and resolve the 
problem before operating 
your model again.

Stop immediately at the first 
sign of weak batteries. Never 
turn the transmitter off when 
the battery pack is plugged 
in. The model could run out 
of control.

RADIO SYSTEM CONTROLS

5

Always turn your

transmitter on first.

Turn on the model.

1

2

Plug in the battery.

3

Forward

Neutral

Brake/Reverse

TURN

 R

IG

H

T

T

U

RN

 LEFT

Drive*

Park*

*See page 20 for information on rocker switch operation. 

Summary of Contents for 68086-21





































Reviews: