Traxxas 6407X Owner'S Manual Download | Manualshive

Page: 24 / 36

background image

24

•

XO-1

Suspension and Cush Drive assembly removal

Your model was designed with ease of disassembly in mind. The entire front and rear suspension assemblies can be removed from the
chassis fully intact with the removal of only a few screws. Refer to the exploded views included in the Service and Support Guide for
complete assembly diagrams.

•

Removing the front suspension module

1. Remove the four 4x15 countersunk screws from the underside of the chassis.
2. Remove the two 4x18 button head screws from the front of the chassis brace.
3. Remove the 3x15 button head screws from the steering servo horn.
4. Pull the front suspension assembly away from the chassis.

•

Removing the rear suspension module
(Cush drive assembly removal)

1. Remove the two 3x25 countersunk screws from the underside of the chassis.
2. Remove the two 3x15 countersunk screws from the underside of the chassis.
3. Remove the two 4x12 button head screws from the chassis brace.
4. Pull the rear suspension assembly away from the chassis.
5. Remove the Cush Drive (removing the two 3x10 button head screws that thread

into the motor mount through the chassis brace may help flex the chassis
brace out of the way).

MAINTAINING YOUR MODEL

4x18BCS

4x12BCS

3x15BCS

4x15CCS

3x15CCS

3x25CCS

Rear Suspension

Assembly

Front Suspension

Assembly

Cush Drive

Assembly

«
...
22
23
24
25
26
...
»

Summary of Contents for 6407X





































Reviews:

No comments

Related manuals for 6407X

Brand: ModelCraft Pages: 8

Brand: PR RACING Pages: 26

Brand: Team Losi Pages: 11

Brand: H-KING Pages: 8

Brand: Skyrc Pages: 2

Brand: Jamara Pages: 12

LTO SPORT OVAL RACER

Brand: RJ Speed Pages: 6

AUTO TRANSPORT TRAILER

Brand: REVELL Pages: 16

Brand: Viessmann Pages: 4

Brand: Yokomo Pages: 28

FEBER tribike PLANET

Brand: Famosa Pages: 4

Brand: Reely Pages: 96

Brand: Reely Pages: 120

Brand: Amewi Pages: 24

Brand: Gmade Pages: 28

Brand: ACME Pages: 4

Brand: Ying Hao Toys Pages: 6

Brand: ZERO-X Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands