Traxxas 4810 Owner'S Manual Download | Manualshive

Page: 30 / 48

background image

The TRX 2.5 Racing Engine

30

The Traxxas EZ-Start Electric Starting System

The Traxxas EZ-Start brings the convenience of push-button
electric engine starting to your Nitro 4-Tec. The EZ-Start consists
of a hand-held control unit and an on-board motorized starter.

Power for the EZ-Start system comes from a 7.2-volt
rechargeable NiCad battery pack installed in the hand-held
control unit (battery not included).
The engine glow plug is heated automatically by the
EZ-Start system, eliminating the need to keep up with a
separate glow plug igniter.
The voltage to the glow plug is kept constant, regardless of
the load placed on the starter by the starter motor.
The “Glow Plug” LED (light emitting diode) on the control
unit indicates the condition of the glow plug.
The “Motor” LED indicates the status of the EZ-Start electric
starter motor.
The cush drive mechanism in the drive unit prevents
damage to the gears caused by engine kickback.
Smart Start

™

protection circuitry prevents damage to the

motor by cutting power if the load on the motor or other
electronics exceeds safe limits.

Installing the EZ-Start Battery

The EZ-Start system requires a fully charged 7.2-volt NiCad
battery pack (not included). Use a charger (not included)
designed for 7.2-volt battery packs. Charge the battery
according to the charger manufacturer’s directions.

1.

Press the tab in the end of the battery compartment door
to open

2.

Plug a fully charged 7.2-volt NiCad battery pack into the
connector inside.

3.

Twist the battery 2 or 3 times to twirl the battery plug wires.
This helps hold the wire and battery in place when the
battery is installed in the compartment

4.

Place the battery into the compartment and press the wires
securely into place.

5.

Slide the battery compartment door back on and lock the
end tab.

▼▼▼▼▼

▼

▼

Use the
Right Charger

The most convenient

type of charger is an AC
peak-detecting charger that
plugs directly into an AC
wall outlet. It contains
special peak-detection
circuitry that automatically
shuts the charger off when
the battery is fully charged.

If you’re using a 15-minute
timed charger, always fully
discharge the battery pack
before each charge. Some
high mAh battery packs
(1500 mAh or higher)
require more than the
standard 15 minutes of
charge time. If the battery
pack is cold after 15 minutes
of charging, add another 5
minutes of charge time.
Closely monitor the battery
pack and stop charging it
when it begins to feel warm
to the touch. Never leave a
battery charging
unattended. Always follow
charger manufacturer’s
instructions.

«
...
28
29
30
31
32
...
»

Summary of Contents for 4810

















































Reviews:

No comments

Related manuals for 4810

Brand: Duratrax Pages: 20

Brand: TeamC Racing Pages: 36

Rubber Band Race Car

Brand: S&S Worldwide Pages: 2

1969 Camaro Convertible

Brand: REVELL Pages: 8

HotWheels RC Radio Control Master Blaster 91810

Brand: Toy State Pages: 4

Brand: O’Donnel Racing Pages: 36

Brand: AE Pages: 34

Brand: Enabling Devices Pages: 2

Brand: Kool Karz Playground Pages: 15

Brand: Yokomo Pages: 32

Fortnite The Baller

Brand: Jazwares Pages: 2

Blippi RC Racecar

Brand: Jazwares Pages: 2

Fire Fighter Mercedes-Benz Antos

Brand: Jamara Pages: 8

Brand: Jamara Pages: 4

Brand: Faller Pages: 8

Safari Sounds Microphone

Brand: VTech Pages: 10

Sit, Stand & Ride Baby Walker

Brand: VTech Pages: 13

switch & go dinos bronco the triceratops

Brand: VTech Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands