background image

E-MAXX BRUSHLESS • 15

driving at high speed, or on tracks that favor sweeping turns 
where gentle steering inputs are required. The ranges are 
exaggerated for illustrative purposes.

Experiment! Try varying degrees of exponential. It’s easy to go back 
to “zero” if you don’t like the effect. There’s no wrong way to adjust 
exponential. Any setting that makes you more comfortable with 
your model’s handling is the “right setting.” 

SETTING UP THE ANTENNA

The receiver antenna has been set up 
and installed from the factory. 
When reinstalling the antenna, first 
slide the antenna wire into the bottom 
of the antenna tube until the white tip 
of the antenna is at the top of the tube 
under the black cap. Insert the base of 
the tube into the antenna post. Take 
care not to crimp the antenna wire. 
Slide the crimp nut over the antenna 
tube and screw it onto the antenna 
post. Use the supplied tool to tighten 
the crimp nut on the post just until the 
antenna tube is securely in place. Do 
not overtighten or crush the antenna 
wire against the chassis. 

Do not bend or 

kink the antenna wire! See the sidebar 
for more information. Do not shorten 
the antenna tube.

ADJUSTING THE ELECTRONIC 

SPEED CONTROL

The MXL-6s speed control should not need reprogramming with 
normal use

; however, if you install a different radio system in your 

model, or change the transmitter’s throttle-neutral setting from 
50/50 to 70/30, you will need to reprogram the speed control. 
Follow these instructions to reprogram the speed control:

1. Install the batteries of  your choice in the battery compartments 

and plug the batteries into the speed control. 

2. Switch on your transmitter. 
3. Hold full throttle while you switch on the MXL-6s controller. After 

a few seconds, you will hear multiple tones and the RED LED will 
light. 

4. Hold full brake. After a few seconds, you will hear multiple tones  

and the YELLOW LED will light. 

5. Release the trigger to the neutral position. After a few seconds,  

you will hear multiple tones and ALL THE LEDs will light. 

6. Wait a few more seconds for the speed control to ‘arm,’ indicated 

by a double-tone. You are now ready to drive. 

Disconnect Batteries After Use

Always disconnect the batteries from the speed control when  
you are finished using your vehicle. The switch on the speed 
control only shuts off power to the receiver and servos. The speed 
control continues to draw power as long as it is plugged in and 
may over-discharge your batteries if they are left connected to the 
speed control.  

Turning Range  

at Transmitter

Antenna 

Tip

Antenna 

Tube

Antenna 

Mount

Antenna 

Nut

Antenna 

Nut Wrench

Effective Turning 

Range on Model

MXL-6s Specs

Cells:

  

18 NiCad / NiMH 6s LiPo

Resistance: 

0.0003 Ohms per phase

Brake : 

Proportional with  

adjustable curve

Reversible:

 

Yes - with lockout

Low Voltage Cutoff:

 

Programmable

Case Size:

2.2” x 1.9” x 1.4”

Weight with Wires:

121g

Connector Type:

6.5mm bullet

Summary of Contents for 39085 E-MAXX
































Reviews: