background image

1/16 SLASH 4WD • 7

The Quick Start Guide is 
not intended to replace the 
full operating instructions 
available in this manual. 
Please read this entire 
manual for complete 
instructions on the proper 
use and maintenance of 
your model.

Look for the Quick Start 
logo at the bottom of 
Quick Start pages.

The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom 
corners of Quick Start pages.

     1.   Read the safety precautions on page 3

     7.   Check servo operation • See page 14

For your own safety, understand where carelessness and misuse 
could lead to personal injury.

Make sure the steering servo is working correctly.

     2.   Charge the battery pack • See page 11

     8.   Range test the radio system • See page 14

Fully charge the battery pack included with your model. 

Follow this procedure to make sure your radio system works properly 
at a distance and that there is no interference from outside sources.

     3.   Install the antenna • See page 11

     9.   Detail your model • See page 5

The receiver antenna and antenna tube must be properly installed 
before operating your model.

Apply other decals if desired.

     4.   Install batteries in the transmitter • See page 11

     10.  Drive your model • See page 18

The transmitter requires 4 AA alkaline or rechargeable batteries.

Driving tips and adjustments for your model.

     5.   Install the battery pack • See page 11

     11.  Maintaining your model • See page 25

Install the included battery pack in your model.

Follow these critical steps to maintain the performance 
of your model and keep it in excellent running condition.

     6.   Turn on the radio system • See page 13

Make a habit of turning the transmitter on first and off last.

QUICK START: GETTING UP TO SPEED

Summary of Contents for 1/16 SLASH 4x4 70054



























Reviews: