manualshive.com logo in svg

Traxon AL MT LT DW 1000 1QPXL CR CE, Installation Manual

Share
Download
Traxon AL MT LT DW 1000 1QPXL CR CE Installation Manual Download Page 11

www.traxontechnologies.com

©2021 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. 
PATENTS, JAPAN PATENTS, OTHER PATENTS PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide

IG????EN V1.0 11/21 

11 of 21

3.   SAFETY AND OPERATION

• 

CAUTION - Unplug the power supply from the mains power before connecting any cables 

as this can damage the products.

• 

CAUTION - Avoid looking directly into the LED light source at close range for your own 

safety.

• 

Persons installing this product should make sure:

1.  The installation complies with all applicable codes, state and local laws, 

ordinances, standards and safety regulations.

2.  The installation environment is carefully studied and suitable surge protection 

measure(s) is taken.

3.  He or she is qualified for the handling of electrical equipment.

• 

Do not attempt to install or use the product until installation instructions and safety labels 

are fully understood. This product is designed for indoor and outdoor use.

• 

Ensure product operates within the specified temperature range. (Refer to 7. TECHNICAL 

SPECIFICATION for more details.)

• 

The Allegro Media Tube Lite does not contain any user-serviceable parts. Opening of the 

luminaire will void the warranty. 

• 

Do not use the product if any part of it, or the power cables are damaged.

• 

Only use product for specified voltage, do not exceed. (Refer to 7. TECHNICAL 

SPECIFICATION for more details.)

• 

Always maintain connection to ensure waterproofing.

• 

If the product has been subjected to drastic temperature variances, for example, following 

transportation, do not connect the fixture until it has reached room temperature, as 
moisture condensation may cause electric shock and product damages.

• 

When installing the products and system power supplies, please ensure they will not be 

exposed to moisture and extreme heat (and direct sunlight for outdoor products). Besides, 
keep a clean operating environment for the fixtures and system power supplies.

• 

Please study this Installation Guide thoroughly and check the latest Technical Specification 

Sheets available from the Traxon website www.traxontechnologies.com before setup.

• 

Any non-compliance of the Installation Guide will void the Traxon warranty.

Summary of Contents for AL MT LT DW 1000 1QPXL CR CE






















Reviews:

No comments

Brands by name

Popular brands

Load more brands