Transtech PQI 301 Operator'S Handbook Manual Download Page 34

Page: 34 / 36

FAQ’S

Is the PQI orange carry case watertight?

No, the case is not watertight and should not be left out in the rain.

Can the battery be replaced in the field?

No, There are no user serviceable parts, it must be sent back to the

factory.

Do you have to calibrate the PQI annually at the factory?

No, unless you experience a problem with the unit it does not need

to be sent back.

Can I use the PQI 301 on soils, or stone base?

At this time the PQI 301 is only designed for use on Asphalt Pavement.

How can I charge the PQI 301 in my car?

We suggest that you purchase a 12 volt DC to 120 volt AC power

inverter from a local retailer and plug the PQI charger into the inverter.

Follow the inverter instructions.

www.transtechsys.com - 1-800-724-6306

7500-0199

PQI 301 AC Charger

7500-0142

PQI 301 Old Style

AC Charger

7500-0209

PQI 301 DC Vehicle

Charger

Replacement Parts

Order parts online at

www.transtechsys.com/opencart

Scan QR with your

mobile device to go

directly to the store

Summary of Contents for PQI 301





































Search results

Summary of Contents for PQI 301

Reviews:

Related manuals for PQI 301

Brands by name

Popular brands

Transtech PQI 301, Operator'S Handbook Manual

Search results

Summary of Contents for PQI 301

Reviews:

Related manuals for PQI 301

Brands by name

Popular brands