manualshive.com logo in svg

Transition Networks HB-E-TX-8, User Manual

Share
Download
Transition Networks HB-E-TX-8 User Manual Download Page 8

LAN Master™ TX8

10

5

100BASE-TX 8-Port Hub

3. INSTALLATION

NOTE:  LAN Master™ TX8 Link Integrity cannot be disabled. All
devices connected to the LAN Master™ TX8 MUST have link functions
enabled.  
To install the LAN Master™ TX8:

•  Unpack the LAN Master™ TX8 Hub.
•

Install LAN Master™ TX8 on shelf or in rack

•

Optionally cascade LAN Master™ TX8 hubs

•

Connect 100BASE-TX cable to LAN Master™ TX8

•

Connect the LAN Master™ TX8 to power.

Direction is provided in the pages that follow.

Unpacking the LAN Master™ TX8

The LAN Master™ TX8 packing contents should include the following:

Item

Part Number

LAN Master™ TX8

HB-E-TX-8

Power Cord

3344, 3347, 3348, 3349, or 3523, 

(depending upon power configuration 
in country where installed)

User’s Guide

33012

4. OPERATION

The LAN Master™ TX8 normally requires no intervention beyond
occasionally monitoring  the Power and Port Status LEDs.

Status LEDs

Status LEDs are located at the front of the LAN Master™ TX8.

P(

O

)

W

(

E

)

R

Illuminated green:  Hub powered ON.

C

OL

(

LISION

)

Illuminated amber: Collision detected during
data transmission on ANY port.

L

INK

/A

CTIVITY

Illuminated green: Port link established.
Flashing green: Data being received.

P

ARTITION

/J

ABBER

Flashing yellow: Data jabber and error
detected on port.
Illuminated yellow: Port partitioned and
isolated.

Summary of Contents for HB-E-TX-8











Reviews:

No comments

Brands by name

Popular brands

Load more brands