Transition Networks E-TBT-HB-1002 User Manual Download Page 3

TRANSITION Networks, Inc.

24 Port 10BaseT Ethernet Hub

Model E-TBT-HB-1002

Installation Manual

Introduction

The 24 port 10BaseT Ethernet hub, Model E-TBT-HB-1002,
is an Ethernet repeater that provides an economical and
efficient networking system. It is rack mountable and is
designed to meet the IEEE 802.3 10BaseT standards.
Several repeaters can be cascaded together via
thicknet/thinnet coaxial cable, fiber optic cable and/or twist-
ed pair cable to build a large Ethernet network.  The 24 port
hub allows simple installation and expansion flexibility for
your future networking requirements.

About 10BaseT (twisted pair) Topology

The IEEE 802.3 10BaseT specification is defined as
Ethernet across twisted pair wire.  This new technology for
Ethernet (across twisted pair wire) represents a step forward
in network cabling and management.  Since 10BaseT uti-
lizes twisted pair wire, the cost of networking is considerably
less expensive than using coaxial cables.  It is also much
easier to install since it uses RJ-45 modular connectors.

Ethernet thick and thin (coax) networks are designed in a
linear “bus” or “daisy chain” topology where 10BaseT (twist-
ed pair) networks are designed in a “star” type topology.  In
a “star” topology the hub is located in the center of the con-
figuration, with the individual nodes connected to the hub,
spread out like spokes on a wheel.  In a linear or “bus”
topology, if you disconnect a device or accidentally open a

Table 3:  Approved European Power Cord Set Information

Alternate Markings

Surface

Utilizing

Printed or Embossed

black-red-yellow

Harmonization

(thread length/mm)

Approval    Organization

Marking                  Black Red

Yellow

Belgium:

Comite Electro-

CEBEC-HAR

10

30

10

technique Beige (CEBEC)

Verband Deutscher Elektro-

VDE-HAR

30

10

10

techniker (VDE)e, V., Prufstelle

Technique de l'Electricite (UTE)   UTE-HAR

30

30

10

Institute del Marchio Qualita

IEMMEQU-HAR

10

30

50

British Approvals Service for

BASEC-HAR

10

10

30

Electric Cables (BASEC)

N.V. tot Keuring van Electro- KEMA-KEUR-HAR

10 

30

30

technische Matarialien (KEMA)

Svenska Elecktriska (SMEKO)    SEMKO-HAR

10

10

50

Osterreichnischer Verband fur

OVE-HAR

30

10

50

Electrotechnik (OVE)

Danmarks Elektriske (DEMKO)    DEMKO-HAR

30

10

30

Materielkontroll

Institute for Industrial (IIRS)

IIRS-HAR

30

30

50

Research and Standards

Norges Elektriske (NEMKO) 

NEMKO-HAR

10

10

70

Materielkontroll

National Standards Authority

NSAI-HAR

30

30

50

of Ireland (NSAI)

Summary of Contents for E-TBT-HB-1002











Reviews: