Transition Networks E-PSW-FX-02 User Manual Download Page 1

Page: 1 / 16

TRANSITION NETWORKS’ POCKET SWITCH

TECHNICAL SPECIFICATIONS

Standards

IEEE 802.3, IEEE 802.3u

Dimension

4.75" X 5.75" X 1.0"

(120mm x 146mm x 25mm)

Power Supply

NOTE:

Replace power supply only with the equivalent input rating (see below) and

output rating (regulated 12VDC at 1.5 A).

TN PN

Requirement

Location

3507

240 volts, 50 hertz

United Kingdom

3342

230 volts, 50 hertz

Europe

3340

120 volts, 60 hertz

USA/Canada/Mexico

3346

100 volts, 50-60 hertz

Japan

3511

240 volts, 50 hertz

Australia

3537

(with power cord: 3522)

South Africa

Environment

Temperature:

0-50°C (32° to 122° F )

Humidity

10-90%, non condensing

Altitude

0-10,000 feet

Warranty

Lifetime

Transition Networks’

For assistance in installing, using, or
maintaining the TRANSITION Networks
Pocket Switch, contact TRANSITION
Networks Technical Support

at:

(800) 260-1312

or contact your local distributor.

33015.B

(E-PSW-TX-02, E-PSW-FX-02)

Pocket Switch

Transition Networks’

Summary of Contents for E-PSW-FX-02

















Search results

Summary of Contents for E-PSW-FX-02

Reviews:

Related manuals for E-PSW-FX-02

Brands by name

Popular brands

Transition Networks E-PSW-FX-02, User Manual

Search results

Summary of Contents for E-PSW-FX-02

Reviews:

Related manuals for E-PSW-FX-02

Brands by name

Popular brands