CSETF10xx IN THE NETWORK
The CSETF10xx receives and transmits network signals in either full-
duplex or half-duplex mode (depending upon the network devices to
which the media converter is attached). Fast Ethernet
™
in full-duplex
mode allows the maximum cable distances shown on these pages. Fast
Ethernet
™
in half-duplex mode requires attention to the 512-bit Rule
(See page 4).
NOTE: Both copper and fiber connections to the CSETF10xx must be at
the same media-speed: 10BASE-T AND 10BASE-FL OR 100BASE-TX AND
100BASE-SX – unless one or both network connections is capable of
auto-negotiation. The CSETF10xx media converter is designed to work
effectively with 10/100 auto-negotiating ports to provide reliable 10
Mb/s or 100 Mb/s fiber links.
Network Configurations
Install two CSETF10xx series media converters in series to extend, over
fiber, the distance between two 10BASE-T or two 100BASE-TX devices:
TECHNICAL SPECIFICATIONS
Standards
IEEE 802.3,
Compliant with pending TIA/EIA-785 specification
Dimensions
3.4" x 0.86" x 5.0" (86mm x 22mm x 127mm)
Weight
8 oz (approximate)
Power Consumption
3.6 watts
Environment
Typical Operating Temperature*: 0-50°C (32° to 122° F )
Storage Temperature:
-20 to 85°C
Humidity
10-90%, non condensing
Altitude
0-10,000 feet
Warranty
Lifetime
*Operating temperature range for this Slide-In-Module depends on the physical
characteristics and the installation configuration of the TRANSITION Networks
chassis in which this Slide-In-Module will be installed. See the User’s Guide for
the chassis in which this Slide-In-Module will be installed for a discussion of
temperature-related installation constraints.
DECLARATION OF CONFORMITY
Name of Mfg:
Transition Networks
6475 City West Parkway, Minneapolis MN 55344 USA
Model:
CSETF10xx Series Media Converters
Part Number(s):
CSETF1011, CSETF1013, CSETF1018
Regulation:
EMC Directive 89/336/EEC
Purpose: To declare that the CSETF10xx to which this declaration refers is in
conformity with the following standards.
EMC-CISPR 22: 1985 Class A&B; EN 55022: 1988 Class A&B; EN 50082-1:1992;
EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950
I, the undersigned, hereby declare that the equipment specified above conforms to the
above Directive(s) and Standard(s).
_April 16, 2000_____
Stephen Anderson, Vice-President of Engineering
Date
10BASE-T
INPOR
T
MCCM10
MGMT MASTER
RX
TX
LNK
PWR
OUTPOR
T
RESET
DB-9
12C
12C-1
TERM
INIT
CETTF100
CFETF110
LKF
PWR
RXF
RXC
LKC
SPD
PWR
FRX
CRX
FLNK
CLNK
RX
TX
10/100TX
RX
TX
10/100SX
CFETF100
SPD
PWR
FRX
CRX
FLNK
CLNK
RX
TX
100BASE-FX
10BASE-T
10BASE-FL
Media
Conversion
Center
Power
In Use
1
Power
In Use
2
PWR
LKC
SPD
FRX
CRX
10/100TX
RX
TX
10/100SX
SPD
PWR
FRX
CRX
FLNK
CLNK
RX
TX
100BASE-FX
10BASE-T
INPOR
T
MCCM10
MGMT MASTER
RX
TX
LNK
PWR
OUTPOR
T
RESET
DB-9
12C
12C-1
TERM
INIT
CETTF100
CFETF110
LKF
PWR
RXF
RXC
LKC
SPD
PWR
FRX
CRX
FLNK
CLNK
RX
TX
10/100TX
RX
TX
10/100SX
CFETF100
SPD
PWR
FRX
CRX
FLNK
CLNK
RX
TX
100BASE-FX
10BASE-T
10BASE-FL
Media
Conversion
Center
Power
In Use
1
Power
In Use
2
PWR
LKC
SPD
FRX
CRX
10/100TX
RX
TX
10/100SX
SPD
PWR
FRX
CRX
FLNK
CLNK
RX
TX
100BASE-FX
