CGETF10xx IN THE NETWORK
Install two CGETF10xx series media converters in series to extend, over
fiber, the distance between two 1000BASE-TX devices. Or use one
CGETF10xx media converter to connect a 1000BASE-TX terminal
device and a 1000BASE-SX/LX hub, switch, or router. Or use one
CGETF10xx media converter to connect a 1000BASE-TX hub, switch, or
router and a 1000BASE-SX/LX terminal device.
NOTE: A TRANSITION Networks stand-alone media converter can be installed
in series with a TRANSITION Networks chassis media converter that has a
related model number, such as an SGETF10xx with a CGETF10xx.
INSTALLATION
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting switch and when installing Slide-in-Module in the
Media Conversion Center. Failure to observe this caution could result in
damage to, and subsequent failure of, the Media Converter Slide-in-Module.
Set 3-Position Jumper
NOTE: Jumper is located on Media Converter Slide-in-Module circuit board.
Use small needle-nosed pliers or similar device to set
jumper. Refer to drawing for jumper positions.
HARDWARE Converter mode is determined by 4-position
switch settings below.
SOFTWARE Converter mode is determined by most-
recently-saved on-board microprocessor settings.
Set 4-Position Switch
NOTE: Switch is located on Media Converter Slide-in-Module circuit board.
Use small flatblade screwdriver or
similar device to set recessed
switches. Refer to drawing for
four-position switch locations.
Full/Half-Duplex Advertisement
(UP=Enabled) Allows full-duplex
mode. (DOWN) Allows half-
duplex mode.
Pause Advertisement (UP=Enabled) Allows auto-negotiation pause. (DOWN)
Allows NO auto-negotiation pause.
NOTE: If the Pause feature is present on all network devices attached to the
media converter(s), enable Pause on the media converter(s). Otherwise,
disable Pause on the media converter(s).
LPT (UP=Enabled) Allows a fault EITHER on the copper OR on the fiber side
of the media coverter to stop signal and data transmission on the other side.
(DOWN) Disables LPT.
CATEGORY 5:
Gauge
24 to 22 AWG
Attenuation
22.0 dB /100m @ 100 MHz
Maximum Cable Distance:
100 meters
The Gigabit Ethernet™ network uses all four wire pairs.
The active pairs are pins 1 & 2, pins 3 & 6, pins 4 & 5, and pins 7 & 8. Use only
dedicated wire pairs (such as blue/white & white/blue, orange/white &
white/orange) for the active pins.
NOTE: Straight-through/crossover configuration is automatic.
TECHNICAL SPECIFICATIONS
Standards
IEEE 802.3ab, IEEE 802.3 1998
Data Rate
1000 Mb/s
Dimensions
3.4" x 0.86" x 5.0" (86mm x 22mm x 127mm)
Weight
8 oz (approximate)
Delay
300 nsec
Power Consumption
6.5 Watts
Environment
Typical Operating Temperature*: 0-50°C (32° to 122° F )
Storage Temperature:
-20 to 85°C
Humidity
10-90%, non condensing
Altitude
0-10,000 feet
Warranty
Lifetime
*Operating temperature range for this Slide-In-Module depends on the physical
characteristics and the installation configuration of the TRANSITION Networks
chassis in which this Slide-In-Module will be installed. See the User’s Guide for
the chassis in which this Slide-In-Module will be installed for a discussion of
temperature-related installation constraints.
DECLARATION OF CONFORMITY
Name of Mfg:
Transition Networks
6475 City West Parkway, Minneapolis MN 55344 USA
Model:
CGETF10xx-100 Series Media Converters
Part Number(s):
CGETF1013-100, CGETF1014-100, CGETF1015-100,
CGETF1017-100, CGETF1018-100, CGETF1023-100
Regulation:
EMC Directive 89/336/EEC
Purpose: To declare that the CGETF10xx-100 to which this declaration refers is
in conformity with the following standards.
EMC-CISPR 22: 1985 Class A&B; EN 55022: 1988 Class A&B; EN 50082-1:1992;
EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950
I, the undersigned, hereby declare that the equipment specified above conforms to the
above Directive(s) and Standard(s).
_January 6, 2001_____
Stephen Anderson, Vice-President of Engineering
Date
SOFTWARE MODE
H
S
HARDWARE MODE
H
S
toward network connectors
toward chassis
Not Used
LPT UP=ON
Pause Advertisement UP=ON
Full/Half-Duplex Advertisement UP=ON
