background image

Trademark Notice

All trademarks and registered trademarks are the property of their respective owners.

Copyright Restrictions

© 2001-2003, 2005 Transition Networks.
All rights reserved.  No part of this work may be reproduced or used in any form or by any
means - graphic, electronic, or mechanical - without written permission from Transition
Networks.
Printed in the U.S.A.

33222.E

Contact Us

Technical Support

Technical support is available 24 hours a day
US and Canada:

1-800-260-1312

International:

00-1-952-941-7600

Transition Now

Chat live via the Web with Transition Networks Technical Support.
Log onto 

www.transition.com

and click the 

Transition Now

link.

Web-Based Seminars

Transition Networks provides seminars via live web-based training.
Log onto 

www.transition.com

and click the 

Learning Center

link.

E-Mail

Ask a question anytime by sending an e-mail to our technical support staff.

[email protected]

Address

Transition Networks
6475 City West Parkway
Minneapolis, MN  55344, USA
telephone:

952-941-7600

toll free:

800-526-9267

fax:

952-941-2322

Declaration of Conformity

Name of Mfg:

Transition Networks 

6475 City West Parkway, Minneapolis MN 55344 USA

Model:

CBFTF10xx-12x Series Media Converters

Part Number(s):

CBFTF1011-120, CBFTF1013-120, CBFTF1014-120, CBFTF1015-120, 
CBFTF1016-120, CBFTF1017-120, CBFTF1018-120,  CBFTF1025-120,
CBFTF1029-120, CBFTF1029-121, CBFTF1029-122,  CBFTF1029-123

Regulation:

EMC Directive 89/336/EEC

Purpose:  To declare that the

CBFTF10xx-12x 

to which this declaration refers is

in conformity with the following standards.

CISPR 22: 1993; EN 55022:1994; EN 55024:1998; FCC Part 15 Class A; 

EN 61000-3-2:1995; EN 61000-3-3:1995; 21 CFR subpart J

I, the undersigned, hereby declare that the equipment specified above conforms to the above

Directive(s) and Standard(s).

_April 16, 2001_____

Stephen Anderson, Vice-President of Engineering

Date

Summary of Contents for CBFTF1011-120










Reviews: