Transition Networks C4TEF1011-100 User Manual Download Page 2

2

C4TEF10xx-10x

Technical Support: 

1-800-260-1312

International: 

00-1-952-941-7600

(24 hours)

T1/E1

Link

Link

Link

Link

AIS

AIS

AIS

AIS

TX

RX

C4TEF

LKF

PWR

1

2

3

4

5

6

Fiber Port

RS-232

T1/E1Ports

Part Number

Fiber-Optic 

- single fiber, single mode, 100Base-FX

C4TEF1029-100 

SC, 1310 mn (TX)/1550 nm (RX), 20 km (12.4 miles)*

C4TEF1029-101 

SC, 1550 mn (TX)/1310 nm (RX), 20 km (12.4 miles)*

C4TEF1029

-100

and C4TEF1029

-101

are intended to be installed in the same link

where one is the local converter and the other is the remote converter.

Installation

NOTE:  

Due to proprietary communication over fiber, the C4TEF10xx-10x is

required to be installed in pairs, where one is the local converter and the other is
the remote converter.

Copper and Fiber Ports

The figure below illustrates the locations of the fiber port, the RS-232 port, and
the four (4) T1/E1 ports.  

NOTE:  

An 

RS-232 cable 

with a 6-pin DIN connector and a DB-9 connector is

included with the C4TEF10xx-10x media converter.

C4TEF1029-102 

SC, 1310 mn (TX)/1550 nm (RX), 40 km (24.8 miles)*

C4TEF1029-103 

SC, 1550 mn (TX)/1310 nm (RX), 40 km (24.8 miles)*

C4TEF1029

-102

and C4TEF1029

-103

are intended to be installed in the same link

where one is the local converter and the other is the remote converter.

* Typical maximum cable distance. Actual distance is dependent upon the

physical characteristics of the network.  (TX) = transmit, (RX) = receive

3

[email protected]

-- Click the 

“Transition Now”

link for a live Web chat.

Installation 

-- Continued

Configuration Switches

The C4TEF10xx-10x media converter has two (2) sets of configuration switches.  

Set #1 is on the upper circuit board and sets the 

T1/E1 options

.

Set #2 is on the lower circuit board and sets the 

serial options

.

Use a flat blade screwdriver to set the switches as shown:

Switch Set #1 - T1/E1 Options

1, 2, 3, 4 - Line Settings 

Switches 1, 2, 3, and 4 are used to setup the line settings for the T1/E1 ports.  The
selected setting applies to all four (4) T1/E1 channels.

Switch Set #1:  T1/E1 Options

Switch Set #2:  Serial Options

Key:

up

down

DSX-1, 100 ohm, 266-399 ft. (81-122 m)

DSX-1, 100 ohm, 399-533 ft. (122-162 m)

DSX-1, 100 ohm, 0-133 ft. (0-40.5 m)

DSX-1, 100 ohm, 133-266 ft. (40.5-81 m)

1 2

DS1, 100 ohm, 0 dB LBO

DS1, 100 ohm, -7.5 dB LBO

DSX-1, 100 ohm, 533-655 ft. (162-200 m)

J1, 110 ohm, 0-655 ft. (0-200 m)

3

E1, 120 ohm

DS1, 100 ohm, -15 dB LBO

DS1, 100 ohm, -22.5 dB LBO

4

1 2 3 4

Summary of Contents for C4TEF1011-100












Reviews: