Transcend TS-AKM4 User Manual Download Page 7

Page: 7 / 54

INTRODUCTION

1.4 Specifications and Features

•

CPU

- Supports AMD Duron / Athlon 550MHz~1G+Hz Socket A CPU

•

Chipset

- TS-AKT4:VIA KT133+686A

- TS-AKT4/B:VIA KT133+686B

- TS-AKM4:VIA KT133+686A

- TS-AKM4/B:VIA KT133+686B

•

DRAM Memory

- Supports Synchronous DRAM

- 3 x 168-pin DIMM module sockets on board

- Up to 1.5GB memory size

- 8/16/32/64/128/256/512MB SDRAM, VCM

- Supports ECC

- PC100/PC133/VCM133 SDRAM compliant

•

I/O BUS Slot

- 1 x AGP slot

- 5 x Master/Slave PCI slots (PCI 2.2 compliant)

- 1 x ISA slot

- 1 x AMR slot (Shared with ISA slot)

•

I/O Functions

- Supports PIO Mode 3,4 ATAPI devices and Ultra DMA33/66

- Supports 2 high speed UART 16550 COM ports

- Supports SPP/EPP/ECP LPT port

- Supports 1.44/2.88 MB floppy drive

- Supports PS/2 Mouse and PS/2 Keyboard

- Supports IrDA port

- Supports 4 Universal Serial Bus (USB) ports(USB V1.1 Standard)

- Support S3 Savage 4 3D (TS-AKM4 only)

Summary of Contents for TS-AKM4























































Search results

Summary of Contents for TS-AKM4

Reviews:

Related manuals for TS-AKM4

Brands by name

Popular brands

Transcend TS-AKM4, User Manual

Search results

Summary of Contents for TS-AKM4

Reviews:

Related manuals for TS-AKM4

Brands by name

Popular brands