Trane IntelliPak 1, Installation, Operation And Maintenance Manual, Page: 155 / 164

RT-SVX072A-EN 155
high-pressure sprayer is used:
a. The minimum nozzle spray angle is 15 degrees.
b. Do not allow sprayer pressure to exceed 600 psi.
c. Spray the solution perpendicular (at 90 degrees)
to the coil face.
d. For evaporator and reheat coils, maintain a
minimum clearance of 6" between the sprayer
nozzle and the coil. For microchannel condenser
coils, optimum clearance between the sprayer
nozzle and the microchannel coil is 1"-3”.
6. Spray the leaving-airflow side of the coil first; then
spray the opposite side of the coil. For evaporator
and reheat coils, allow the cleaning solution to
stand on the coil for five minutes.
7. Rinse both sides of the coil with cool, clean water.
8. Inspect both sides of the coil; if it still appears to be
dirty, repeat Steps 6 and 7.
9. Reinstall all of the components and panels removed
in Step 1; then restore power to the unit.
10. For evaporator and reheat coils, use a fin comb to
straighten any coil fins which were inadvertently
bent during the cleaning process.
Steam or Hot Water Coils
To clean a steam or hot water coil, use a soft brush, a
steam-cleaning machine, and water.
1. Verify that switches 1S1 and 1S70 are turned
“OFF”, and that the main unit disconnect is locked
open.
W WA AR RN NIIN NG G
N No o S Stte ep p S Su urrffa acce e!!
F Fa aiillu urre e tto o ffo ollllo ow w iin nssttrru uccttiio on n b be ello ow w cco ou ulld d rre essu ulltt iin n
d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Do o n no ott w wa allkk o on n tth he e ssh he ee ett m me etta all d drra aiin n p pa an n.. W Wa allkkiin ng g
o on n tth he e d drra aiin n p pa an n cco ou ulld d cca au usse e tth he e ssu up pp po orrttiin ng g m me etta all
tto o cco olllla ap psse e a an nd d rre essu ulltt iin n tth he e o op pe erra atto orr//tte ecch hn niicciia an n
ffa alllliin ng g..
2. Remove enough panels and components from the
unit to gain sufficient access to the coil.
3. Straighten any bent coil fins with a fin comb. (Use
the data in to determine the appropriate fin comb
size.)
4. Remove loose dirt and debris from both sides of the
coil with a soft brush.
5. Use the steam-cleaning machine to clean the
leaving-air side of the coil first; start at the top of the
coil and work downward; then clean the entering-
air side of the coil, starting at the top of the coil and
working downward.
6. Check both sides of the coil; if it still appears dirty,
repeat Step 5.
7. Reinstall all of the components and panels removed
in Step 2; then restore power to the unit.
Microchannel Condenser Coil
Repair and Replacement
If microchannel condenser coil repair or replacement is
required, refer to General Service Bulletin RT-SVB83*-
EN for further details.
Fall Restraint
W WA AR RN NIIN NG G
F Fa alllliin ng g O Offff E Eq qu uiip pm me en ntt!!
F Fa aiillu urre e tto o ffo ollllo ow w iin nssttrru uccttiio on nss b be ello ow w cco ou ulld d rre essu ulltt iin n
d de ea atth h o orr sse erriio ou uss iin njju urry y..
T Th hiiss u un niitt iiss b bu uiilltt w wiitth h ffa allll rre essttrra aiin ntt ssllo ottss llo occa atte ed d o on n
u un niitt tto op p tth ha att M MU US ST T b be e u usse ed d d du urriin ng g sse errv viicciin ng g..
T Th he esse e ssllo ottss a arre e tto o b be e u usse ed d w wiitth h ffa allll rre essttrra aiin ntt
e eq qu uiip pm me en ntt tth ha att w wiillll n no ott a allllo ow w a an n iin nd diiv viid du ua all tto o
rre ea acch h tth he e u un niitt e ed dg ge e.. H Ho ow we ev ve err ssu ucch h e eq qu uiip pm me en ntt w wiillll
N NO OT T p prre ev ve en ntt ffa alllliin ng g tto o tth he e g grro ou un nd d,, a ass tth he ey y a arre e N NO OT T
d de essiig gn ne ed d tto o w wiitth hsstta an nd d tth he e ffo orrcce e o off a a ffa alllliin ng g
iin nd diiv viid du ua all..
The fall restraint is located approximately 3 feet from
the unit edge.
Figure 118. Fall restraint
FALL RESTRAINT
Final Process
Record the unit data in the blanks provided.
S Se errv viicce e a an nd d M Ma aiin ntte en na an ncce e