Trane IntelliPak 1, Installation, Operation And Maintenance Manual, Page: 152 / 164

152 RT-SVX072A-EN
N No otte e:: Parameter '4-18 Current Limit' for field
installed TRV200 drives must be set
according to table below for proper operation
and to meet overload protection
requirements. Replacement drive will not run
the compressor until set properly. Factory
installed drives are programmed properly for
unit operation. Parameter 4-18 is available via
the quick menu.
Table 73. Compressor VFD programming parameter 4-18
Unit Tonnage Unit Voltage
200V 230V 460V 575V
20
90% 82% 84%
82%
25
30
92% 84% 80%
40
50
111% 101% 91% 93%
55
60 119% 108% 100% 102%
70 135% 122% 115% 116%
75 111% 101% 91% 93%
Monthly Maintenance
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e w w//C Ca ap pa acciitto orrss!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err a an nd d d diisscch ha arrg ge e
cca ap pa acciitto orrss b be effo orre e sse errv viicciin ng g cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss a an nd d d diisscch ha arrg ge e a allll m mo otto orr sstta arrtt//rru un n
cca ap pa acciitto orrss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an nn no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. F Fo orr v va arriia ab blle e
ffrre eq qu ue en nccy y d drriiv ve ess o orr o otth he err e en ne errg gy y sstto orriin ng g
cco om mp po on ne en nttss p prro ov viid de ed d b by y T Trra an ne e o orr o otth he errss,, rre effe err tto o
tth he e a ap pp prro op prriia atte e m ma an nu uffa accttu urre err’’ss lliitte erra attu urre e ffo orr
a allllo ow wa ab blle e w wa aiittiin ng g p pe erriio od dss ffo orr d diisscch ha arrg ge e o off
cca ap pa acciitto orrss.. V Ve erriiffy y w wiitth h a a C CA AT T IIIIII o orr IIV V v vo ollttm me ette err
rra atte ed d p pe err N NF FP PA A 7 70 0E E tth ha att a allll cca ap pa acciitto orrss h ha av ve e
d diisscch ha arrg ge ed d..
Before completing the following checks, turn the unit
O
OF FF F and lock the main power disconnect switch open.
Filters
Inspect the return air and final filters. Clean or replace
them if necessary. Refer to the Service and
Maintenance chapter for filter information.
Cooling Season
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an n n no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. V Ve erriiffy y tth ha att n no o
p po ow we err iiss p prre esse en ntt w wiitth h a a v vo ollttm me ette err..
☐ Check the unit’s drain pans and condensate piping
to ensure that there are no blockages.
☐ Inspect the evaporator and condenser coils for dirt,
bent fins, etc. If the coils appear dirty, clean them
according to the instructions described in “Coil
Cleaning” later in this section.
☐ Inspect the F/A-R/A damper hinges and pins to
ensure that all moving parts are securely mounted.
Keep the blades clean as necessary.
S Se errv viicce e a an nd d M Ma aiin ntte en na an ncce e