Trane BAYSENS050m Installation Manual Download Page 2

©2020 Trane

 ACC-SVN129D-EN

Introduction

Warnings, Cautions, and Notices

Safety advisories appear throughout this manual as required. Your personal safety and the proper 
operation of this machine depend upon the strict observance of these precautions.

The three types of advisories are defined as follows:

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in 

death or serious injury.

CAUTION

s

Indicates a potentially hazardous situation which, if not avoided, could result in 

minor or moderate injury. It could also be used to alert against unsafe practices.

NOTICE

Indicates a situation that could result in equipment or property-damage only 

accidents.

WARNING

Proper Field Wiring and Grounding Required!

Failure to follow code could result in death or serious injury. All field wiring MUST be 
performed by qualified personnel. Improperly installed and grounded field wiring poses FIRE 
and ELECTROCUTION hazards. To avoid these hazards, you MUST follow requirements for field 
wiring installation and grounding as described in NEC and your local/state electrical codes. 
Failure to follow code could result in death or serious injury. 

WARNING

Hazardous Voltage w/Capacitors!

Failure to disconnect power and discharge capacitors before servicing could result in death or 
serious injury. Disconnect all electric power, including remote disconnects and discharge all 
motor start/run capacitors before servicing. Follow proper lockout/tagout procedures to 
ensure the power cannot be inadvertently energized. For variable frequency drives or other 
energy storing components provided by Trane or others, refer to the appropriate 
manufacturer’s literature for allowable waiting periods for discharge of capacitors. Verify with 
an appropriate voltmeter that all capacitors have discharged.

For additional information regarding the safe discharge of capacitors, see PROD-SVB06A-EN.

Summary of Contents for BAYSENS050m













Reviews: