manualshive.com logo in svg

Trane BAYBARO300 Series, Installation Manual

Share
Download
Trane BAYBARO300 Series Installation Manual Download Page 6

6

ACC-SVN156E-EN

Figure 2.

Barometric assembly (factory installed)

2

Precedent™ Parts List

Item

Description

Qty

1

Right-side barometric relief block-off

1

2

Intermediate block-off panel

1

3

Left-side barometric relief block-off

1

4

Block-off horizontal return assembly

1

5

Barometric relief assembly

1

6

FIABARM003* - Information label

1

7

Cardboard pad package

1

8

Shipping lumber

2

9

Installation guide

1

10

Plastic bag 10.00 in. x 15.00 in.

1

11

Fabricated insulation 1.00T x 1.00 in. x 6.00 in.

2

12

Washer-bonded 0.250 in. x 0.750 in.

8

13

Gasket

1

14

Screws 10-16 UNC x ½ in.

4

15

Screws 10-16 UNC x ¾ in.

43

Figure 3.

Parts (field installed kit)

 1 

 2 

 3 

 4 

 5 

 7 

 8 

 10 

 12 

 13 

 14 

 15 

 6 

 9 

 11 

Installation Bag

 with Screws

Remove Shipping 

Screws

Remove Shipping 

Screws

Remove Shipping

Screws

Figure 4.

Barometric assembly (factory installed)

Remove

Shipping Screws

Remove

Shipping Screws

General Information

Summary of Contents for BAYBARO300 Series

















Reviews:

No comments

Brands by name

Popular brands

Load more brands