background image

WARNING

This equipment is to be serviced by professionally trained personnel 
ONLY. Under NO circumstances should an unqualified person service it. 
This equipment contains refrigerant under PRESSURE and operates at 
HIGH VOLTAGE. Improperly installed, adjusted or altered equipment by an 
unqualified person poses safety hazards including FIRE, ELECTROCUTION, 
or EXPLOSION, which could result in death or serious injury.

Warnings and Cautions

Warnings and Cautions.

 Warnings are provided to alert installing 

contractors to potential hazards that could result in personal injury or 
death, while cautions are designed to alert personnel to conditions that 
could result in equipment damage.

Your personal safety and the proper operation of this machine depend 
upon the strict observance of these precautions.

Attention: 

Warnings and Cautions appear at appropriate sections 

throughout this literature. Read these carefully.

WARNING:

 Indicates a potentially hazardous situation which, if not 

avoided, could result in death or serious injury.

CAUTION:

 

Indicates a potentially hazardous situation which, if not 

avoided, could result in minor or moderate injury. It may also be used 
to alert against unsafe practices.

NOTICE

:

 Indicates a situation that could result in equipment or 

property-damage only accidents.

WARNING

Electrocution and Fire Hazards with Improperly Installed and Grounded 

Field Wiring!
Improperly installed and grounded field wiring poses FIRE & 
ELECTROCUTION hazards. To avoid these hazards, you MUST follow 
requirements for field wiring installation and grounding as described in 
the National Electrical Codes (NEC) and your local/state electrical codes. 
All field wiring MUST be performed by qualified personnel. 
Failure to follow these requirements could result in death or serious injury.

Summary of Contents for American Standard 4MXD8509A





























Reviews: