background image

 

18-AC74D1-4

Min. 12” to 

Shrubbery

Avoid Install 

Near Bedrooms

Min 5’ Unrestricted

Access Panel

Min 3’ 

Unrestricted 

2.3 Suggested Locations for Best Reliability

Ensure the top discharge area is unrestricted for 
at least five (5) feet above the unit.

Three (3) feet clearance must be provided in 
front of the control box (access panels) and any 
other side requiring service. 

Do not locate close to bedrooms as operational 
sounds may be objectionable.

Min. 12” to 

Shrubbery

Min. 12” 

to Wall

Position the outdoor unit a minimum of 12” from 
any wall or surrounding shrubbery to ensure 
adequate airflow.

Outdoor unit location must be far enough away 
from any structure to prevent excess roof runoff 
water from pouring directly on the unit.

2.4 Coastal Considerations

If installed within one mile of salt water, including seacoasts and inland waterways, models without factory 
supplied Seacoast Salt Shields require the addition of BAYSEAC001 (Seacoast Kit) at installation time.  Please 
refer to Application Guide SS-APB006-EN: Trane - Sea Coast Applications and Seascoast Corrosion Protection 
Bulletin
 UN-SVB11A-EN.

Summary of Contents for 4TTX5018A1000A

























Reviews: