background image

www.TrailFX.com

 

Page 

3

 of 

7                                                                                                                                                                                                       

Rev 031318 

 

c. 

Thread  (1)  8mm  Plastic  Retainer  onto  the  threaded  end and  down  tight  against  the body  panel, 

(Figure  5)

NOTE

The  Plastic  Retainer  is  designed  to  keep  the  Bolt/Nut  Plate  from  falling  into  the  body  panel  and  to  aid  in  Bracket 
installation.

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

d. 

Select a driver side Mounting Bracket, 

(Figure  6)

. Attach the Bracket to the threaded end of the Bolt Plate with (1) 

8mm Flat Washer, (1) 8mm Lock Washer and (1) 8mm Hex Nut, 

(Figure 7)

. Do not tighten at this time. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 

e. 

Remove  the  8mm  Hex  Bolt  from  the  nut  on  the  Bolt  Plate from 

Step  3a

.  Rotate the  Bolt on  the  Bolt  Plate until  the 

threaded nut lines up with the remaining hole in the Mounting Bracket and body panel, 

(Figures  7  &  8)

. Attach the 

Bracket to the threaded Nut Plate with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, 

(Figure 8)

. Do not fully tighten hardware at this time.

 

 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 

(Fig 5) Thread Plastic Retainer onto Bolt 
Plate to hold Bole Plate in position. 

Plastic Retainer 
 

Front 

(Fig 6) Driver side Brackets 

Front 

Remove Hex Bolt, rotate Bolt/Nut 
Plate to line up threaded nut with 
body panel and Mounting 
Bracket (see arrow)  

8mm Flat Washer 
8mm Lock Washer 
8mm Hex Nut 

(Fig 7) Attach Bracket to Bolt on Bolt Plate 

Plastic Retainer 
 

Front 

(Fig 8) Remove 8mm Hex Bolt (see Fig 3). Rotate Bolt 
Plate to line up with remaining factory hex shaped hole. 

8mm Hex Bolt 
8mm Lock Washer 
8mm Flat Washer 
 

Summary of Contents for A1537S








Reviews: