8
11
SWITCH FINGER
23
[ 584.10 ]
1
2
18 4 PL'S
21 4 PL'S
19
22
22
22
19
19
15
15
24 4 PL'S
4
A
B
C
D
Z
sy3800110 - 24 X 48 aND 30 X 60 bOaRDs - 180
°
OveR Cab mOuNt Kit
POsitiON sWitCH setuP
limit sWitCH iNstalatiON
Adjusting position switch:
1. Ensure unit is properly assembled and operational.
2. Turn the unit on. With the controller, manually position the sign where it is in the horizontal traveling position.
3. Mount the switch (item 11) to the adjuster plate (item 10) and lightly torque the screws (items 17, 21, and 24), trying not impede the movement of the
switch against the plate.
4. Attach the switch adjuster plate to the to the side of the support using items 16, 21 and 24 as shown in Fig 3, leaving the screws loose enough to adjust
the switch.
5. Move the switch in the direction parallel to the support as shown in Fig 3 until the switch is inline with the center of the switch finger and tighten the bolts.
6. Move the switch up towards the switch finger until you feel the switch click, then tighten the switch down.
7. Using the controller, manually rotate the sign to the full upright position.
8. Double tap the actuator direction button in the down position direction and watch where the sign stops. If the sign stops before the switch finger is inline with
the center of the switch, move the switch out away from the switch finger slightly. If the sign fails to stop in the traveling position, the switch needs to be
moved in towards the switch finger slightly.
9. Once the switch is adjusted properly, make sure the all the bolts are properly tightened and that the wires are routed as to not interfere with the normal
operation of the sign.
10. The switch is now adjusted and the sign is ready for use.
After routing the limit switch wires through the arrow board as described
in the lift kit manual, connect the wires as shown in the figure below.
Note that the photocell wire connected to the black lead on the driver
must be disconnected from the driver and re-connected to the limit
switch harness as shown.
PART
ITEM
QTY
DESCRIPTION
NUMBER
1
1
FRAME, RIGHT, 180°
2
1
FRAME, LEFT, 180°
3
1
PLATE, PIVOT, 30 X 60 AND 24 X 48
4
1
BRACKET, SIGN, 30 X 60 AND 24 x 48
5
1
ACTUATOR, 6” STROKE
SY3800090-A
6*
1
CABLE, ACTUATOR
SY3800090-B
7
1
BRACKET, ACTUATOR
8
1
LINK, SWITCH FINGER
9
1
LINK, #1
10
1
MOUNT, SWITCH
11
1
SWITCH, LIMIT
SY3800100-S
12
1
BOLT, HEX, 1/2-13 X 2
EL185-8100
PART
ITEM
QTY
DESCRIPTION
NUMBER
13
2
BOLT, HEX, 1/2-13 X 2 1/4
SY3900100-F
14
1
BOLT, HEX, 1/2-13 X 2 1/2
SY3900100-N
15
5
BOLT, HEX, 1/2-13 X 3 1/4
SY3800120-V
16
2
SCREW, SLOT, #10-32 X 1 3/4
EL185-3043
17
2
SCREW, SLOT, #10-32 X 7/8
EL185-3041
18
4
BOLT, HEX, 5/16-18 X 3
SY3900100-J
19
14
WASHER, FLAT, 1/2
SY3900100-M
20
6
WASHER, FLAT, #10
EL185-4060
21
4
WASHER, FLAT, 5/16
EL185-6000
22
11
NUT, HEX, LOCKING, 1/2-13
SY3900100-L
23
4
NUT, HEX, LOCKING, #10-32
HY2308208
24
4
NUT, HEX, LOCKING, 5/16-18
SY3900100-K
*Not shown
EL510-3880
Figure 1
Figure 2
Figure 3
3
7
5
8
10
11
17
16
20 6 PL'S
23 4 PL'S
14
13
12
13
22 10 PL'S
19 12 PL'S
9
15
16355 south Lone eLm Road
•
oLathe, Kansas
66062
•
usa
•
toll free: 800-447-3693
•
Phone:
913-780-1440
•
fAX: 913-780-1427
•
emAil: info@
superiorsignals.com
•
www.superiorsignals.com
16355 south Lone eLm Road
•
oLathe, Kansas
66062
•
usa
•
toll free: 800-447-3693
•
Phone:
913-780-1440
•
fAX: 913-780-1427
•
emAil: info@
superiorsignals.com
•
www.superiorsignals.com
16355 south Lone eLm Road • oLathe, Kansas 66062 • usa • toLL fRee: 800-447-3693 • Phone: 913-780-1440 • faX: 913-780-1427 • emaiL: [email protected] • www.superiorsignals.com
