manualshive.com logo in svg

Tradinco TRAQC-1 DPG, User Manual, Page: 27 / 43

Share
Download
Tradinco TRAQC-1 DPG User Manual Download Page 27

User Manual

 

TRAQC-5 
P1000

 

 

 
 

TRAQC-5 P1000 & TRAQC-1 DPG rev.0

 

 

 

page : 27 

12.

 

Introduction TRAQC-1 DPG 

The Traqc-1 DPG is a digital pressure gauge featuring a Min/Max display function.  
Full scale (FS) accuracy of type B is +/-  0.5%, tha accuracy of type P is +/- 0.1%, based on 
the upper limit of the measurement range. Dynamic pressure peaks are measured at a scanning 
rate of 10 ms  
(100 measurement values/second). The MIN/Max memory is continuously updated and 
rewritten.

 

 
 

12.1

 

Notes on safety / production selection 

The correct functioning of the Traqc-1 DPG can only be guaranteed when the specifications 
detailed in these operation instructions are adhered to. In particular, specifications relating to 
the permitted upper limit of the measurement range as well as the permissible temperature 
range must be observed.  

 

Caution! 
Serious malfunctions leading to personal injury or damage to property can result 
from using the chosen product in applications that do not comply with the 
specifications or from disregarding the operating instructions. In particular, 
incorrect mounting of the pressure gauge and the corresponding adapter can 

cause the pressure gauge to be torn out of the assembly. 
For repairs or calibration of the measurement instruments, please contact TRADINCO.  

 
 
 

 

 

Summary of Contents for TRAQC-1 DPG












































Reviews:

No comments