background image

Mattress size: This bed is intended for use only with a standard Twin mattress 74” - 75” long by
37 1/2" - 38 1/2" wide (mattress not included). Use of an incorrectly sized mattress may leave 
space between the edge of the mattress and the edge of the bed. Excess space may result in 
entrapment which may lead to serious injury or death.

Assembled dimensions (approximate): 89" long, 39.5" wide, 24" high.

Model DUMPTR-4 Dump Truck Bed Frame

Revised 04/02/2015

Page 

2 of 6

Use and Warnings

Your child’s safety is our top priority. Please observe the following safety warnings to ensure the safe 
use of this product:

 Weight limitation: minimum weight requirement for this bed is 50 lbs. This product is not to be 

used by any occupant under 50 lbs. Do not let any child under 50 lbs. play or sleep on or around
the bed. Maximum weight is 350 lbs.

 Do not stand or sit on shelf.

 Do not stand, sit, or otherwise occupy or apply weight to bed slats until a mattress or box spring 

has been installed. The slats are not rated or tested for individual loads without the application of
mattress or box spring.

 Do not allow jumping or horseplay on the bed.

 Do not use bed if any parts are missing or damaged.

 Do not use substitute parts. Contact manufacturer should replacement parts be necessary.

 Do not use a water or sleep flotation mattress.

 Before assembly and use, inspect bed for damaged hardware, loose joints, missing pieces or 

sharp edges.

 Warning: hardware included with this product may have sharp points or edges. Assembly by an 

adult is required. Keep all loose hardware out of reach of children.

 Warning: small parts are a choking hazard for children. Make sure that all hardware is properly 

and tightly installed to prevent access to loose parts by children. Properly discard excess 
hardware after assembly to prevent access of loose parts to children. Properly discard all 
packing materials.

 Always make sure the mattress is firmly seated against the headboard. Excess space may 

result in entrapment which may lead to serious injury or death.

●  

General Specifications

Summary of Contents for DUMPTR-4







Reviews: