background image

D. Securites_BSO-EN_v1 08/2017

10

108.2

108.3

108.1

108.1

D.7.  BLOCSTOP BSO fall arrest device

D.7.1. Operation

The safety wire rope passes through a BLOCSTOP™ 

BSO fall arrest device (fig. D1.7). The centrifugal 

weight of the BLOCSTOP™ automatically and conti-

nuously controls the transport speed of the safety wire 

rope through the device. If the speed is too fast, the 

BLOCSTOP™ stops the descent by gripping on the 

safety wire rope.

In an emergency case, the BLOCSTOP™ can be trig-

gered by hand by pressing on the EMERGENCY STOP 

button (108.2) - in particular, in the event of slow 

slip-

page 

of the hoist causing the platform to slope.

D.7.2.  Measures to be taken immediately after 

an incident

Fig. D.7.1 - BLOCSTOP™ BSO

108.1 Lever

108.2 

EMERGENCY STOP button

108.3 

Inspection window

CLOSED

OPEN

OPEN

Fig. D.7.2 – Open the BLOCSTOP™ BSO

The BLOCSTOP™ will engage in the following cases:

A  

Platform lowers with «overspeed»,

B  

Rupture of lifting wire rope or failure of hoist.

In normal operation, the lever (108.1) of the 

BLOCSTOP™ must be in the «OPEN» position (fig. 

D1.7).

Risk of injury by great fall due to 

a safety wire rope which is not 

tensioned between the suspension 

and the BLOCSTOP™. 

If the BLOCSTOP™ is closed when 

the platform is moving up, the 

safety wire rope will not be properly 

tensioned and the BLOCSTOP™ will 

become ineffective.

Case B :

 If the BLOCSTOP™ has engaged subsequent 

to rupture of the lifting wire rope or failure of the hoist:

Evacuate the operator(s).

Secure the equipment by 

appropriate means so that the wire 

rope or hoist can be replaced.

Case A: 

If you can exclude that the lifting wire rope has 

not broken or the hoist has not failed:

1.  Lift the equipment (43) until you have eliminated the 

load on the safety wire rope.

2.  Return the lever (108.1) to the «OPEN» position 

(fig. D.7.2).

3.  Carefully lower the equipment to the ground while 

being ready at all times to press the EMERGENCY 

STOP button (108.2) of the BLOCSTOP™.

4.  Before you continue working, check operation of 

the BLOCSTOP™ as instructed in the following 

pages.

DANGER

DANGER

Summary of Contents for solo 2000




















Reviews: