MODEL NUMBER
SS-13
SS-18
SS-24
SS-32
SS-40
Applications
Video Cassettes;
Printing, Computer
Printing;
Art/Frame
Art/Frame
Computer Software;
Software;Manuals;
General packaging;
Gift Baskets
Gift Baskets
CDs/Tapes
CDs/Tapes
Damaged Package
Posters; Retail
Posters; Retail
Books/Magazines
Hardwares
Recovery
Packaging
Packaging
Length of Sealing Area
13”
18”
24”
32”
40”
Maximum Film Width
13”
18”
24”
32”
40”
Maximum Film Weight
100LBS
100LBS
100LBS
100LBS
100LBS
Film Core Diameter
1-7/8” & 3”
1-7/8” & 3”
1-7/8” & 3”
1-7/8” & 3”
1-7/8” & 3”
Power Supply (Primary)
110VAC*
110VAC*
110VAC*
110VAC*
110VAC*
Voltage (Secondary)(Deluxe)
14VAC
20VAC
30VAC
38VAC
38VAC
Amperage
3amps
5amps
5amps
8amps
8amps
Cycles
50/60hz. 1 phase
50/60hz. 1 phase
50/60hz. 1 phase
50/60hz. 1 phase
50/60hz. 1 phase
HEAT GUN
110 A/C - 60hz. - 1100 watts -- Temperature range: 50º F. to 1100º F. Weight: 2LB.
* 220 VAC also available upon request.
ON OFF SWITCH
RA901VB-BIV
TIMER
TD-100
POWER CORD
6550-8
FUSE HOLDER
342-828
FUSE HOLDER
342-828
COVER
1340 CO
TRANSFORMER*
INNER BRKT
1340-1B
ARMSPRING
E-5109
OUTER BRKT
1340 OB
ROLLER*
SPREADER BRACKET
1340 SB
KNOB
75 KN
THREADED STUD
95412A542
ARM*
PHENOLIC ASSEMBLY*
NICHROME WIRE*
TEFLON TAPE
TT10-RL
SEALING PAD*
C-CHANNEL*
INSULATOR*
BASE*
GROUND WIRE
* PART NUMBER SPECIFIC TO MACHINE SIZE
SPECIFICATIONS
CHASSIS
1340-CH
A C OUTLET
AC-PREP
0
3
0
8
0
1
0
1
S
S
M
A
N
P
D
F
TROUBLE SHOOTING / RECOMMENDATIONS
Symptom:
Centerfold shrink film will not separate or open.
Recommendation:
If shrink film appears to be single sheet, place a strip of tape on top of the film and on the bottom and pull
apart to initially separate.
Symptom:
Film appears to smoke or is sticking to wire when seal is made.
Recommendation:
This can mean one of several things:
1. With PP or PO film, wire must be kept clean by removing sealing pad
and depressing arm until wire burns clean all film residue. No Teflon tape
required on arm.
2. PVC film will smoke when seal is made. Teflon tape over the heating
element will prevent the film from smoking and will occasionally need to
be replaced. For Teflon tape or other parts, call the service number.
Symptom:
Burning holes in shrink film with the heat gun.
Recommendation:
If gun is set on high temperature and held in the same spot for
more than a few seconds, the film will burn. Gun should be continually moving in a
circular spiral motion from the outside edges of the package first, and to the middle
of the package last.
Symptom:
Arm is not properly cutting and sealing shrink film.
Recommendation:
1. On/Off switch may not be turned on.
2. Timer on Deluxe Model may not be set properly.
3. Arm may not be in complete contact with pad. (Gentle Pressure).
4. Excessive pressure applied to sealing arm.
5. Wire may need cleaning.
Symptom:
Setting timer properly on the Deluxe Model.
Recommendation:
Timer should be set to allow the minimal amount of time necessary to cut and seal the film. The setting
will vary according to type of film in use. Setting timer too high will burn the film. PVC film will require a lower setting than
most other films. Timer may need to be adjusted to lower setting as machine is used in a continuous or
rapid manner.
The air inside the package expands as the
film is heated. The quickest way to vent the
film is to cut what amounts to an asterisk (*)
into the closed end of the centerfold. The
smaller your package, the more lines you
should cut to make sure every package has
at least one vent hole. This will prevent
package from ballooning.
Cut Slits 1/16” deep
Closed end
of centerfold
Open end
of centerfold
Venting Your Shrink Package