S A F E T Y
TO START ENGINE
ALWAYS start the engine in the open air
DO NOT smoke when refuelling
DO NOT mix OIL with the fuel
ALWAYS stop the engine before making any adjustments,
refuelling, moving or cleaning, or when the unit is
unattended
USE ONLY unleaded petrol from fuel containers designed for
this purpose - refuel outdoors only and replace the tank
cap securely
IN CASE of petrol spillage move the machines away from the
area of spillage and allow the petrol vapours to dissipate
before starting the engine
DO NOT remove any safety guards that are fitted
DO NOT touch any moving parts or attempt any maintenance
whilst the machine is running - KEEP HANDS AND FEET
AWAY
BEFORE starting work clear the work area of any objects that
could damage the machine
DO NOT allow children or anyone uninstructed to operate the
machine - KEEP ANIMALS AWAY
ENSURE the machine is on firm, level ground - DO NOT use
machine on a slope
ALWAYS wear suitable clothing to give personal protection
including footwear that offers a good grip
AVOID wearing loose garments that may catch in moving
parts
KNOW how to stop the machine in an emergency
NEVER interfere with any control settings on the engine
IF A FAULT develops DO NOT attempt any repair -
immediately contact the supplier from whom the
machine was obtained
VISUALLY INSPECT the machine before use - ensure all nuts
and bolts are tight and not worn or damaged
KEEP IN MIND the operator is responsible for accidents or
hazards occurring to people or property
WEAR eye and ear protection
Ensure the discharge chute and feed chute are in the operating
position.
Check the engine oil level. Top up with 10w/40 oil if necessary.
Check fuel level. Only use unleaded petrol from a clean container.
Never re-fuel when the engine is hot or running. Leave 1” air
space in the fuel tank.
Switch on ignition and if the engine is cold, apply the choke.
Turn the fuel tap to ‘on’ position and apply half throttle.
Pull the recoil start handle gently until it engages then give it a
good strong pull to start the engine.
When the engine has started, release the choke lever after a few
seconds and return the throttle lever to idle position.
OPERATION
TO STOP ENGINE
MAINTENANCE GUIDE
DANGER POINTS TO OBSERVE
Increase engine to FULL throttle and allow the machine to build up to
its FULL operating speed.
Use the timber sizing ring to ensure the maximum thickness of timber
is not exceeded. If the timber does not go through the ring it is too
large for the machine to handle.
Timber less than 1” in diameter usually self-feeds through the
machine. If it is over 1” in diameter, it may be necessary to pull the
timber back to avoid over-feeding if the engine speed starts to drop.
Always put the thickest end of the branch into the chute first.
FAILURE TO OBSERVE THIS PRECAUTION WILL CAUSE
DAMAGE - correct feed pressure and engine speed is important to
reduce the possibility of damage to the machine.
Neither pull out nor push in the short end pieces with hands. Use the
next branch to feed the short end through the chipper each time. BE
CAREFUL - short ends sometimes feed themselves through the
chipper but are occasionally thrown out.
Clear processed material regularly, do not allow it to build up
underneath the machine.
Empty the collection bag regularly if used.
NEVER overload the machine.
NEVER stand in front of the chipper chute when the machine is
operating.
NEVER position the machine on a ledge higher or lower than the
operator. Machine and operator must be on the same level.
ALWAYS operate the machine a FULL throttle.
ALWAYS allow the machine to run at full speed for 2 minutes before
switching off.
Allow the machine to cool down before moving the discharge and
infeed chute for transportation.
WARNING - The exhaust may be hot.
TURN OFF THE FUEL TAP BEFORE TRANSPORTING THE
MACHINE.
FAILURE TO OBSERVE THESE POINTS MAY RESULT IN
PERSONAL INJURY.
If you are using the collection bag over the discharge chute then
ensure it is not obstructing the exhaust as damage to the bag will
occur from a hot exhaust.
Never stand on the discharge side of the machine or directly in front of
the chipper chute.
KEEP TO ONE SIDE.
For engine maintenance please refer to engine manufacturers
manual.
Close the throttle.
Turn ignition switch to ‘OFF’ position.
WARNING: THE EXHAUST COVER MAY BE HOT - DO NOT
TOUCH
After every hour of operation:
Stop engine. Remove the spark plug cap
Check engine oil level. (Recommended oil SAE 10w/40).
Do not turn the machine on its side for cleaning.
Refit the spark plug cap.
